manualshive.com logo in svg

Renesas SH7616, Hardware Manual

The Renesas SH7616 is a high-performance microcontroller, equipped with advanced features for seamless functionality. Unlock its full potential by accessing the comprehensive Hardware Manual. Easily available for free download at manualshive.com, this manual provides detailed instructions and insights, enabling users to maximize the capabilities of this exceptional product.

Share
Download
background image

Section 9   Ethernet Controller (EtherC)

Rev. 2.00  Mar 09, 2006  page 383 of 906

REJ09B0292-0200

9.2.2

EtherC Status Register (ECSR)

Bit:

31

30

29

. . .

11

10

9

8

—

—

—

.  .  .

—

—

—

—

Initial value:

0

0

0

. . .

0

0

0

0

R/W:

R

R

R

.  .  .

R

R

R

R

Bit:

7

6

5

4

3

2

1

0

—

—

—

—

—

LCHNG

MPD

ICD

Initial value:

0

0

0

0

0

0

0

0

R/W:

R

R

R

R

R

R/W

*

R/W

*

R/W

*

Note: 

*

The flag is cleared by writing 1.  Writing 0 does not affect the flag.

The EtherC status register shows the internal status of the EtherC. This status information can be
reported to the CPU by means of interrupts. Individual bits are cleared by writing 1 to them. For
bits that generate an interrupt, the interrupt can be enabled or disabled by means of the
corresponding bit in the EtherC status interrupt permission register (ECSIPR).

Bits 31 to 3—Reserved: These bits are always read as 0. The write value should always be 0.

Bit 2—LINK Signal Changed (LCHNG): Indicates that the LNKSTA signal input from the PHY-
LSI has changed from high to low, or from low to high. This bit is cleared by writing 1 to it.
Writing 0 to this bit has no effect.

Bit 2:  LCHNG

Description

0

LNKSTA signal change has not been detected

(Initial value)

1

LNKSTA signal change (high-to-low or low-to-high) has been detected

Notes: 1. The current link status can be checked by referencing the LMON bit in the PHY

interface status register (PSR).

2. Signal variation may be detected when the LNKSTA function is selected by the port A

control register (PACR) of the pin function controller (PFC).

Bit 1—Magic Packet Detection (MPD): Indicates that a Magic Packet has been detected on the
line. This bit is cleared by writing 1 to it. Writing 0 to this bit has no effect.

Bit 1:  MPD

Description

0

Magic Packet has not been detected

(Initial value)

1

Magic Packet has been detected

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

Salusfin SF-930EU User'S Installation Manual preview
SF-930EU
Brand: Salusfin Pages: 6
Riverbed SteelCentral NetExpress Installation Manual preview
SteelCentral NetExpress
Brand: Riverbed Pages: 38
Valcom VIP-822A Quick Start Manual preview
VIP-822A
Brand: Valcom Pages: 4
SurfControl 509-8629-00 Setup Manual preview
509-8629-00
Brand: SurfControl Pages: 2
B&B Electronics PCMCIA High Speed Serial Card CE 232HSPCC User Manual preview
PCMCIA High Speed Serial Card CE 232HSPCC
Brand: B&B Electronics Pages: 14
Supermicro X12SPO-NTF/-F User Manual preview
X12SPO-NTF/-F
Brand: Supermicro Pages: 131
ExtraHop EDA 4200 Install preview
EDA 4200
Brand: ExtraHop Pages: 2
Lanner NCA-6520 User Manual preview
NCA-6520
Brand: Lanner Pages: 141
Extreme Networks ExtremeCloud Appliance E1120 User Manual preview
ExtremeCloud Appliance E1120
Brand: Extreme Networks Pages: 219
Hologic ThinPrep 3000 Operator'S Manual preview
ThinPrep 3000
Brand: Hologic Pages: 256
Kordis NCB210X2-DS-AB Datasheet preview
NCB210X2-DS-AB
Brand: Kordis Pages: 31
ZALMAN CNPS9700 LED User Manual preview
CNPS9700 LED
Brand: ZALMAN Pages: 8
Gigamon GigaVUE H Series Hardware Installation Manual preview
GigaVUE H Series
Brand: Gigamon Pages: 55
Johnson Controls Metasys NAE55 Installation Manual preview
Metasys NAE55
Brand: Johnson Controls Pages: 20
Ekselans 250022 User Manual preview
250022
Brand: Ekselans Pages: 5
Korg EXB-RADIAS Owner'S Manual preview
EXB-RADIAS
Brand: Korg Pages: 78
JVC Milestone VR-N1600 Brochure & Specs preview
Milestone VR-N1600
Brand: JVC Pages: 6
JVC VR-X1600U Instructions Manual preview
VR-X1600U
Brand: JVC Pages: 204

Brands by name

Popular brands

Load more brands