Renesas SH7616 Hardware Manual Download Page 178 | Manualshive

Page: 178 / 935

background image

Section 5 Interrupt Controller (INTC)

Rev. 2.00 Mar 09, 2006 page 152 of 906
REJ09B0292-0200

5.2.6

On-chip Peripheral Module Interrupts

On-chip peripheral module interrupts are interrupts generated by the following 9 on-chip
peripheral modules:

•

Direct memory access controller (DMAC)

•

Bus state controller (BSC)

•

Watchdog timer (WDT)

•

16-bit free-running timer (FRT)

•

Ethernet controller direct memory access controller (E-DMAC) (Including EtherC interrupt)

•

16-bit timer pulse unit (TPU)

•

Serial communication interface with FIFO (SCIF)

•

Serial I/O with FIFO (SIOF)

•

Serial I/O (SIO)

A different interrupt vector is assigned to each interrupt source, so the exception service routine
does not have to decide which interrupt has occurred. Priority levels between 0 and 15 can be
assigned to individual on-chip peripheral modules in interrupt priority registers A, B, D, and E
(IPRA, IPRB, IPRD, IPRE). On-chip peripheral module interrupt exception handling sets the
interrupt mask level bits (I3–I0) in the status register (SR) to the priority level value of the on-chip
peripheral module interrupt that was accepted.

5.2.7

Interrupt Exception Vectors and Priority Order

Table 5.4 lists interrupt sources and their vector numbers, vector table address offsets and interrupt
priorities.

Each interrupt source is allocated a different vector number and vector table address offset. Vector
table addresses are calculated from vector numbers and vector table address offsets. In interrupt
exception handling, the exception service routine start address is fetched from the vector table
entry indicated by the vector table address. See table 4.4, Calculating Exception Vector Table
Addresses, in section 4, Exception Handling, for more information on this calculation.

IRL interrupts IRL15–IRL1 have interrupt priority levels of 15–1, respectively. IRQ interrupt and
on-chip peripheral module interrupt priorities can be set freely between 0 and 15 for each module
by setting interrupt priority registers A–E (IPRA–IPRE). The ranking of interrupt sources for
IPRA–IPRE, however, must be the order listed under Priority within IPR Setting Unit in table 5.4
and cannot be changed. A reset assigns priority level 0 to on-chip peripheral module interrupts. If
the same priority level is assigned to two or more interrupt sources and interrupts from those

«
...
176
177
178
179
180
...
»

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

Brand: Garmin Pages: 2

Brand: Ubiquiti Pages: 23

Brand: Tripp Lite Pages: 20

MultiConnect SE MTS2EA

Brand: Multitech Pages: 8

Brand: JETWAY Pages: 55

Brand: Lanner Pages: 59

Brand: Nakayo Pages: 119

Brand: Rainbow Pages: 2

Brand: Intercoax Pages: 2

Brand: PADAUK Pages: 27

DAS-1800HR Series

Brand: Keithley Pages: 139

SecPath F50X0 Series

Brand: H3C Pages: 41

Fibe-Air IP-10G

Brand: Ceragon Pages: 71

Brand: Enterasys Pages: 2

7798 I/SITE LAN

Brand: CSI Pages: 56

Brand: Radio Shack Pages: 154

CNPS8900 Series

Brand: ZALMAN Pages: 10

Brand: Hama Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands