manualshive.com logo in svg

Renesas SH7616, Hardware Manual

The Renesas SH7616 is a high-performance microcontroller, equipped with advanced features for seamless functionality. Unlock its full potential by accessing the comprehensive Hardware Manual. Easily available for free download at manualshive.com, this manual provides detailed instructions and insights, enabling users to maximize the capabilities of this exceptional product.

Share
Download
background image

Section 9   Ethernet Controller (EtherC)

Rev. 2.00  Mar 09, 2006  page 414 of 906
REJ09B0292-0200

destination address. The fact that the CAMSEN is asserted is reflected in the RFAR bit in the
EtherC/E-DMAC status register (EESR) and this can be reflected as the write-back information of
the descriptor.

Table 9.3   Processing of Receive Frames

CAMSEN Input

Frame Type

Normal Mode

Promise-CAS Mode

Asserted

SH7616 MAC address

Discarded

Discarded

(address is

Broadcast address

Discarded

Discarded

matched)

Multicast address

Discarded

Discarded

CAM MAC addresses

Received

Discarded

Negated

SH7616 MAC address

Received

Received

(address is not

Broadcast address

Received

Received

matched)

Multicast address

Received

Received

CAM MAC addresses

Discarded

Received

RX-CLK

RX-DV

RXD3 to RXD0

CAMSEN

SFD

Preamble

Destination address

Within 35 clock cycles

Figure 9.8   CAM Signal Timing

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

NEC N8141-75F Startup Manual preview
N8141-75F
Brand: NEC Pages: 6
IEI Technology HPE-4S1 Quick Installation Manual preview
HPE-4S1
Brand: IEI Technology Pages: 3
Moxa Technologies UC-8100 Series Hardware User Manual preview
UC-8100 Series
Brand: Moxa Technologies Pages: 19
T.A HALL 6370 Instruction Manual preview
HALL 6370
Brand: T.A Pages: 11
HMS Networks Anybus Communicator ABC4021 User Manual preview
Anybus Communicator ABC4021
Brand: HMS Networks Pages: 60
ZKTeco HVR0402 User Manual preview
HVR0402
Brand: ZKTeco Pages: 68
H3C LSWM12H2Q User Manual preview
LSWM12H2Q
Brand: H3C Pages: 9
B-G Instruments DataPlot CB1224 Manual preview
DataPlot CB1224
Brand: B-G Instruments Pages: 4
ebm-papst R3G560-AH02-03 Operating Instructions Manual preview
R3G560-AH02-03
Brand: ebm-papst Pages: 13
PADAUK PDK5S-P-003 User Manual preview
PDK5S-P-003
Brand: PADAUK Pages: 27
Navitar 1-62643 Dimensional Drawing preview
1-62643
Brand: Navitar Pages: 1
Cypress Semiconductor CY7C1410JV18 Specification Sheet preview
CY7C1410JV18
Brand: Cypress Semiconductor Pages: 26
Kontron PC/104-PCMCIA-1 User Manual preview
PC/104-PCMCIA-1
Brand: Kontron Pages: 20
Arctic Freezer i32 Welcome Manual preview
Freezer i32
Brand: Arctic Pages: 7
Alphacool NexXxoS GPX-N 970 M03 Instruction Manual preview
NexXxoS GPX-N 970 M03
Brand: Alphacool Pages: 2
INGENIA Everest CORE Product Manual preview
Everest CORE
Brand: INGENIA Pages: 58
KEB 1MF5280-7008 Instruction Manual preview
1MF5280-7008
Brand: KEB Pages: 32
3Ware 9500S-8 - Escalade RAID Controller User Manual preview
9500S-8 - Escalade RAID Controller
Brand: 3Ware Pages: 46

Brands by name

Popular brands

Load more brands