manualshive.com logo in svg

Renesas SH7616, Hardware Manual

The Renesas SH7616 is a high-performance microcontroller, equipped with advanced features for seamless functionality. Unlock its full potential by accessing the comprehensive Hardware Manual. Easily available for free download at manualshive.com, this manual provides detailed instructions and insights, enabling users to maximize the capabilities of this exceptional product.

Share
Download
background image

Section 14   Serial Communication Interface with FIFO (SCIF)

Rev. 2.00  Mar 09, 2006  page 630 of 906
REJ09B0292-0200

14.4

SCIF Interrupt Sources and the DMAC

The SCIF has four interrupt sources: the break interrupt (BRI) request, receive-error interrupt
(ERI) request, receive-FIFO-data-full interrupt (RXI) request, and transmit-FIFO-data-empty
interrupt (TXI) request.

Table 14.13 shows the interrupt sources and their relative priorities. The interrupt sources can be
enabled or disabled with the TIE or RIE bit in SCSCR. Each kind of interrupt request is sent to the
interrupt controller independently.

When the TDFE flag is set to 1 in the serial status 1 register (SC1SSR), a TXI interrupt is
requested. A TXI interrupt request can activate the DMAC to perform data transfer. The TDFE bit
is cleared to 0 automatically when all writes to the transmit FIFO data register (SCFTDR) by the
DMAC are completed.

When the RDF flag is set to 1 in SC1SSR, an RXI interrupt is requested. An RXI interrupt request
can activate the DMAC to perform data transfer. The RDF bit is cleared to 0 automatically when
all receive FIFO data register (SCFRDR) reads by the DMAC are completed.

When the ER flag is set to 1, an ERI interrupt is requested. The DMAC cannot be activated by an
ERI interrupt request.

When the BRK flag is set to 1, a BRI interrupt is requested. The DMAC cannot be activated by a
BRI interrupt request.

A TXI interrupt indicates that transmit data can be written, and an RXI interrupt indicates that
there is receive data in SCFRDR.

Table 14.13 SCIF Interrupt Sources

 

Interrupt Source

 

Description

 

DMAC
Activation

 

Priority on
Reset Release

ERI

 

Receive error (ER)

 

Not possible

 

High

RXI

 

Receive data full (RDF) or data ready (DR)

 

Possible
(RDF only)

  

↑

BRI

 

Break (BRK)

 

Not possible

  

↓

TXI

 

Transmit data FIFO empty (TDFE)

 

Possible

 

Low

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

D-Link xStack Storage DSN-4000 Series Datasheet preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 5
National Instruments PXIe-8240 Getting Started preview
PXIe-8240
Brand: National Instruments Pages: 9
National Instruments FIELDPOINT FP-1600 Operating Instructions Manual preview
FIELDPOINT FP-1600
Brand: National Instruments Pages: 8
Quantum LightSpeed Appliance QLS250 Owner'S Manual preview
LightSpeed Appliance QLS250
Brand: Quantum Pages: 12
STONEFLY DR365V-2404 Setup Manual preview
DR365V-2404
Brand: STONEFLY Pages: 48
PairGain PG-FLEX RT FRL-752 Manual preview
PG-FLEX RT FRL-752
Brand: PairGain Pages: 6
B&B Electronics Parallel & Serial Port Checker PPC User Manual preview
Parallel & Serial Port Checker PPC
Brand: B&B Electronics Pages: 4
IDT Digital Encoder Plus User Manual preview
Digital Encoder Plus
Brand: IDT Pages: 98
3Com FEM656C Quick Start Manual preview
FEM656C
Brand: 3Com Pages: 53
Konica Minolta SRX-101A Operation Manual preview
SRX-101A
Brand: Konica Minolta Pages: 31
Renesas PROM Programming Adapters PCA7438F-64A User Manual preview
PROM Programming Adapters PCA7438F-64A
Brand: Renesas Pages: 18
Freescale Semiconductor M68HC08 series Designer Reference Manual preview
M68HC08 series
Brand: Freescale Semiconductor Pages: 124
Adaptec RAID 5085 Release Notes preview
RAID 5085
Brand: Adaptec Pages: 2
IBM 25CPC710 Application Note preview
25CPC710
Brand: IBM Pages: 8
Adaptec ASR-3085 Important Information About Issues And Errata preview
ASR-3085
Brand: Adaptec Pages: 3
Fibocom H330SS Hardware User Manual preview
H330SS
Brand: Fibocom Pages: 39
Ecolab EcoJet EcoStar 1500 Installation & Operation Manual preview
EcoJet EcoStar 1500
Brand: Ecolab Pages: 80
ICP DAS USA ZT-2005-C8 User Manual preview
ZT-2005-C8
Brand: ICP DAS USA Pages: 60

Brands by name

Popular brands

Load more brands