Renesas SH7616 Hardware Manual Download Page 732 | Manualshive

Page: 732 / 935

background image

Section 17 16-Bit Timer Pulse Unit (TPU)

Rev. 2.00 Mar 09, 2006 page 706 of 906
REJ09B0292-0200

Bits 2 to 0—Counter Start 2 to 0 (CST2 to CST0): These bits select operation or stoppage for
TCNT.

Bit n: CSTn

Description

0

TCNTn count operation is stopped

(Initial value)

1

TCNTn performs count operation

Note: n = 2 to 0

If 0 is written to the CST bit during operation with the TIOC pin designated for output, the
counter stops, but the TIOC pin output compare output level is retained. If TIOR is written to
when the CST bit is cleared to 0, the pin output level will be changed to the set initial output
value.

17.2.9

Timer Synchronous Register (TSYR)

Bit:

7

6

5

4

3

2

1

0

—

—

—

—

—

SYNC2 SYNC1 SYNC0

Initial value:

0

0

0

0

0

0

0

0

R/W:

R

R

R

R

R

R/W

R/W

R/W

TSYR is an 8-bit readable/writable register that selects independent operation or synchronous
operation for the channel 0 to 2 TCNT counters. A channel performs synchronous operation when
the corresponding bit in TSYR is set to 1.

TSYR is initialized to H'00 by a reset.

Bits 7 to 3—Reserved: These bits are always read as 0. The write value should always be 0.

Bits 2 to 0—Timer Synchro 2 to 0 (SYNC2 to SYNC0): These bits select whether operation is
independent of or synchronized with other channels.

When synchronous operation is selected, synchronous presetting of multiple channels*

1

, and

synchronous clearing through counter clearing on another channel*

2

are possible.

Bit n: SYNCn

Description

0

TCNTn operates independently

(Initial value)

TCNT presetting/clearing is unrelated to other channels

1

TCNTn performs synchronous operation
TCNT synchronous presetting/synchronous clearing is possible

Notes: n = 2 to 0

1. To set synchronous operation, the SYNC bits for two channels at least must be set to 1.
2. To set synchronous clearing, in addition to the SYNC bit , the TCNT clearing source

must also be set by means of bits CCLR2 to CCLR0 in TCR.

«
...
730
731
732
733
734
...
»

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

Brand: Rabbit Pages: 45

Brand: Rabbit Pages: 174

Brand: Rabbit Pages: 43

Brand: Idis Pages: 85

Brand: Lattice Semiconductor Pages: 43

ACCULINK 3161 CSU

Brand: Paradyne Pages: 19

Brand: PairGain Pages: 80

Brand: FOR-A Pages: 37

CamCon FCS-4000

Brand: LevelOne Pages: 94

GigaVUE H Series

Brand: Gigamon Pages: 55

Brand: Foscam Pages: 92

Brand: B&B Electronics Pages: 90

BS2000 SE Series

Brand: Fujitsu Pages: 43

BS2000 SE Series

Brand: Fujitsu Pages: 93

Brand: Fujitsu Pages: 5

Brand: Faroudja Pages: 17

BL10e - HP ProLiant - 512 MB RAM

Brand: Compaq Pages: 228

CCR1009-7G-1C-1S+

Brand: MikroTik Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands