manualshive.com logo in svg

Renesas SH7616, Hardware Manual

The Renesas SH7616 is a high-performance microcontroller, equipped with advanced features for seamless functionality. Unlock its full potential by accessing the comprehensive Hardware Manual. Easily available for free download at manualshive.com, this manual provides detailed instructions and insights, enabling users to maximize the capabilities of this exceptional product.

Share
Download
background image

Section 1   Overview

Rev. 2.00  Mar 09, 2006  page 7 of 906

REJ09B0292-0200

Item

Specifications

Direct memory
access controller
(DMAC),
2 channels

•

  4-Gbyte address space, maximum 16M (16,777,216) transfers

•

  Selection of 8-bit, 16-bit, 32-bit, or 16-byte transfer data length

•

  Parallel execution of CPU instruction processing and DMA operation

possible in case of cache hit

•

  Selection of dual address or single address mode

  Single address (data transfer rate of one transfer unit in one bus cycle)

  Dual address (data transfer rate of one transfer unit in two bus cycles)

  When synchronous DRAM is connected, 16-byte continuous read 

→

continuous write transfer is possible (dual)

•

  When SDRAM is connected, clocked single-address transfer is possible at

rates up to 31.25 MHz

•

  Cycle stealing or burst transfer

•

  Relative channel priorities can be set (fixed mode/round robin mode)

•

  DMA transfer is possible for the following devices:

  External memory, on-chip memory, on-chip supporting modules

(excluding DMAC, BSC, UBC, cache, E-DMAC, EtherC)

•

  External requests, DMA transfer requests from on-chip supporting

modules, auto requests

•

  Interrupt request (DEIn) can be issued to CPU at end of data transfer

•

  DACK used for DREQ sampling (however, there is always one overrun as

there is one acceptance before first DACK)

On-chip RAM

•

 4-kbyte 

X-RAM

•

 4-kbyte 

Y-RAM

Ethernet controller
direct memory
access controller
(E-DMAC),
2 channels

•

  Transfer possible between EtherC and external memory/on-chip memory

•

  16-byte burst transfer possible

•

  Single address transfer

•

  Chain block transfer

•

  32-bit transfer data width

•

  4-Gbyte address space

•

  Data transfer possible from across byte boundaries in transmission

•

  Each transmit and receive FIFO includes 2 kbytes

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

M-Audio Computer Quick Start Manual preview
Computer
Brand: M-Audio Pages: 10
Altera Nios II Hardware Development Manual preview
Nios II
Brand: Altera Pages: 42
Hauppauge WinTV-DVB Installation And Reference Manual preview
WinTV-DVB
Brand: Hauppauge Pages: 62
Gearlinx NR4400 Series User'S Quick Start Manual preview
NR4400 Series
Brand: Gearlinx Pages: 23
Keysight Technologies U3024AH10 User'S And Service Manual preview
U3024AH10
Brand: Keysight Technologies Pages: 106
Kentrox RMM-1400 Configuration Manual preview
RMM-1400
Brand: Kentrox Pages: 246
Oracle Acme Packet 3900 Hardware Installation And Maintenance Manual preview
Acme Packet 3900
Brand: Oracle Pages: 70
Kontron PC/104-PCMCIA-1 User Manual preview
PC/104-PCMCIA-1
Brand: Kontron Pages: 20
MSI MS-6593 ATX Instructions preview
MS-6593 ATX
Brand: MSI Pages: 5
Lenze EPZ Series Mounting Instructions preview
EPZ Series
Brand: Lenze Pages: 29
NEC IE-703089-MC-EM1 User Manual preview
IE-703089-MC-EM1
Brand: NEC Pages: 35
NEC DS2000 IntraMail Feature Handbook preview
DS2000 IntraMail
Brand: NEC Pages: 216
NEC IE-703017-MC-EM1 User Manual preview
IE-703017-MC-EM1
Brand: NEC Pages: 33
NEC IE-703040-MC-EM1 User Manual preview
IE-703040-MC-EM1
Brand: NEC Pages: 35
NEC IE-703242-G1-EM1 Preliminary User'S Manual preview
IE-703242-G1-EM1
Brand: NEC Pages: 42
NEC IE-703204-G1-EM1 User Manual preview
IE-703204-G1-EM1
Brand: NEC Pages: 45
NEC IE-703002-MC User Manual preview
IE-703002-MC
Brand: NEC Pages: 63
NEC IE-70000-MC-NW-A User Manual preview
IE-70000-MC-NW-A
Brand: NEC Pages: 29

Brands by name

Popular brands

Load more brands