manualshive.com logo in svg

Renesas SH7616, Hardware Manual

The Renesas SH7616 is a high-performance microcontroller, equipped with advanced features for seamless functionality. Unlock its full potential by accessing the comprehensive Hardware Manual. Easily available for free download at manualshive.com, this manual provides detailed instructions and insights, enabling users to maximize the capabilities of this exceptional product.

Share
Download
background image

Section 9   Ethernet Controller (EtherC)

Rev. 2.00  Mar 09, 2006  page 381 of 906

REJ09B0292-0200

Bit 12—Permit Receive CRC Error Frame (PRCEF): Specifies the treatment of a receive frame
containing a CRC error.

Bit 12:  PRCEF

Description

0

Reception of a frame with a CRC error is treated as an error

(Initial value)

1

Reception of a frame with a CRC error is not treated as an error

Note: When this bit is set to 1, the CRC error frame counter register (CEFCR: see section 9.2.14)

is not incremented when a CRC error is detected.

Bits 11 and 10—Reserved: These bits are always read as 0. The write value should always be 0.

Bit 9—Magic Packet Detection Enable (MPDE): Enables or disables Magic Packet detection by
hardware to allow activation from the Ethernet. When the Magic Packet is detected, it is reflected
to the EtherC status register and the WOL pin notifies peripheral LSIs that the Magic Packet has
been received.

Bit 9:  MPDE

Description

0

Magic Packet detection is not enabled

(Initial value)

1

Magic Packet detection is enabled

Bits 8 and 7—Reserved: These bits are always read as 0. The write value should always be 0.

Bit 6—Receiver Enable (RE): Enables or disables the receiver.

Bit 6:  RE

Description

0

Receiver is disabled

(Initial value)

1

Receiver is enabled

Note: If a switch is made from the receiver-enabled state (RE = 1) to the receiver-disabled state

(RE = 0) while a frame is being received, the receiver will not be disabled until reception of
the frame is completed.

Bit 5—Transmitter Enable (TE): Enables or disables the transmitter.

Bit 5:  TE

Description

0

Transmitter is disabled

(Initial value)

1

Transmitter is enabled

Note: If a switch is made from the transmitter-enabled state (TE = 1) to the transmitter-disabled

state (TE = 0) while a frame is being transmitted, the transmitter will not be disabled until
transmission of the frame is completed.

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

Omnia 11 Installation And Operation Manual preview
11
Brand: Omnia Pages: 102
3Com 3C16080 Important Information preview
3C16080
Brand: 3Com Pages: 2
3Com 3C421600A Quick Setup Manual preview
3C421600A
Brand: 3Com Pages: 74
3Com 3C421600A Installation Manual preview
3C421600A
Brand: 3Com Pages: 6
Garland P1GCCAS Installation Manual preview
P1GCCAS
Brand: Garland Pages: 4
Paradyne 8540 Installation Instructions Manual preview
8540
Brand: Paradyne Pages: 12
T&D RTR-50 User Manual preview
RTR-50
Brand: T&D Pages: 122
TC-Helicon PERFORM-VK Quick Start Manual preview
PERFORM-VK
Brand: TC-Helicon Pages: 2
3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Brand: 3Com Pages: 204
NEC N8141-75F Startup Manual preview
N8141-75F
Brand: NEC Pages: 6
Opvimus UMX-ETH+ Operating Instructions Manual preview
UMX-ETH+
Brand: Opvimus Pages: 12
Intel NetStructure ZT 5515 Product Specification preview
NetStructure ZT 5515
Brand: Intel Pages: 90
Black Box LT2060A Manual preview
LT2060A
Brand: Black Box Pages: 37
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Brand: C-Com Pages: 148
Compro Technology RS-2104 Quick Installation Manual preview
RS-2104
Brand: Compro Technology Pages: 2
mikroElektronika Pressure click Quick Start Manual preview
Pressure click
Brand: mikroElektronika Pages: 2
PairGain PG-Flex FLC-704 Manual preview
PG-Flex FLC-704
Brand: PairGain Pages: 20
3Com 3C433279A Release Note preview
3C433279A
Brand: 3Com Pages: 12

Brands by name

Popular brands

Load more brands