Renesas SH7616 Hardware Manual Download Page 595 | Manualshive

Page: 595 / 935

background image

Section 14 Serial Communication Interface with FIFO (SCIF)

Rev. 2.00 Mar 09, 2006 page 569 of 906

REJ09B0292-0200

Bit 3—Multiprocessor Interrupt Enable (MPIE): Enables or disables multiprocessor interrupts.
The MPIE bit setting is only valid in asynchronous mode when the MP bit in SCSMR is set to 1.

The MPIE bit setting is invalid in synchronous mode and IrDA mode, and when the MP bit is 0.

Bit 3: MPIE

Description

0

Multiprocessor interrupts disabled (normal reception performed) (Initial value)
[Clearing conditions]

•

When the MPIE bit is cleared to 0

•

When data with MPB = 1 is received

1

Multiprocessor interrupts enabled

*

Receive interrupt (RXI) requests, receive-error interrupt (ERI) requests, and
setting of the RDF and FER in SC1SSR and ORER in SC2SSR are disabled
until data with the multiprocessor bit set to 1 is received.

Note:

*

Receive data transfer from SCRSR to SCFRDR, receive error detection, and setting of the
RDF and FER in SC1SSR and ORER flags in SC2SSR, is not performed. When receive
data with MPB = 1 is received, the MPB flag in SC2SSR is set to 1, the MPIE bit is cleared
to 0 automatically, and generation of RXI and ERI (when the RIE bit in SCSCR is set to 1)
and FER and ORER flag setting is enabled.

Bit 2—Reserved: This bit is always read as 0. The write value should always be 0.

Bits 1 and 0—Clock Enable 1 and 0 (CKE1, CKE0): These bits are used to select the SCIF clock
source and enable or disable clock output from the SCK pin. The combination of the CKE1 and
CKE0 bits determines whether the SCK pin functions as the serial clock output pin or the serial
clock input pin. The function of the SCK pin should be selected with the pin function controller
(PFC).

The setting of the CKE0 bit, however, is only valid for internal clock operation (CKE1 = 0) in
asynchronous mode. The CKE0 bit setting is invalid in synchronous mode and in the case of
external clock operation (CKE1 = 1). The CKE1 and CKE0 bits must be set before determining
the SCIF’s operating mode with SCSMR.

For details of clock source selection, see table 14.9 in section 14.3, Operation.

«
...
593
594
595
596
597
...
»

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

Brand: National Instruments Pages: 85

Brand: Roland Pages: 2

Brand: Realtek Pages: 30

Supero SAS-826A

Brand: Supero Pages: 16

DM/IP601-CPCI-100BT

Brand: Dialogic Pages: 2

Brand: Waves Pages: 41

EK-Quantum Momentum ROG Rampage VI Encore

Brand: EK Pages: 11

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Brand: Intel Pages: 86

Brand: TRENDnet Pages: 12

Bluespoon 17-1000

Brand: Radio Shack Pages: 1

Brand: XtendLan Pages: 21

Brand: Ariesys Pages: 10

Brand: IBM Pages: 130

Brand: Echo Pages: 21

CL-SOM-AM57 Series

Brand: CompuLab Pages: 79

Brand: Renesas Pages: 40

Brand: ETAS Pages: 36

Brand: Vxl Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands