Renesas SH7616 Hardware Manual Download Page 378 | Manualshive

Page: 378 / 935

background image

Section 7 Bus State Controller (BSC)

Rev. 2.00 Mar 09, 2006 page 352 of 906
REJ09B0292-0200

peripheral module enables an access to the on-chip peripheral module without having to wait for
the completion of the write to low-speed memory.

During reads, the CPU always has to wait for the end of the operation. To immediately continue
processing after checking that the write to the device of actual data has ended, perform a dummy
read access to the same address consecutively to check that the write has ended.

The bus state controller’s write buffer functions in the same way during accesses from the DMAC.
A dual-address DMA transfer thus starts in the next read cycle without waiting for the end of the
write cycle. When both the source address and destination address of the DMA are external spaces
to the chip, however, it must wait until the completion of the previous write cycle before starting
the next read cycle.

The E-DMAC can perform access involving external memory, but not access involving any on-
chip memory or peripheral modules.

7.10.3

STATS1 and STATS0 Pins

The SH7616 has two pins, STATS1 and STATS0, to identify the bus master status. The signals
output from these pins show the external access status. Encoded output is provided for the
following categories: CPU (cache hit/cache disable), DMAC (external access only), E-DMAC,
and Others (refresh, internal access, etc..). All output is synchronized with the address signals.
The encoding patterns are shown in table 7.9, and the output timing in figure 7.59.

Table 7.9

Encoding Patterns

Identification

STATS1

STATS0

CPU

0

0

DMAC

1

E-DMAC

1

0

Others

1

«
...
376
377
378
379
380
...
»

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

Enterprise Filter Authentication R3000

Brand: 8e6 Technologies Pages: 66

Brand: LaCie Pages: 4

Brand: LaCie Pages: 4

Brand: Zonet Pages: 2

RabbitCore RCM4400W

Brand: Rabbit Pages: 126

Duinotech Lilypad Plus XC3920

Brand: Jaycar Electronics Pages: 2

Brand: Magma Pages: 2

Brand: Cypress Semiconductor Pages: 15

Brand: ATTO Technology Pages: 2

Brand: Ebyte Pages: 23

Brand: NEC Pages: 47

H8S/2615 Series

Brand: Renesas Pages: 28

Brand: Hameg Pages: 46

SECURE BOOT STICK FX

Brand: Ecos Pages: 22

Brand: Epson Pages: 559

Aironet 1200 Series

Brand: Cisco Pages: 138

2432 - IAD Router

Brand: Cisco Pages: 86

Brand: Cisco Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands