Renesas SH7616 Hardware Manual Download Page 453 | Manualshive

Page: 453 / 935

background image

Section 10 Ethernet Controller Direct Memory Access Controller (E-DMAC)

Rev. 2.00 Mar 09, 2006 page 427 of 906

REJ09B0292-0200

transferred to memory when DMA transfer becomes possible. When the frame counter
value falls below 8, another frame is received.

Bit 23—Reserved: These bits are always read as 0. The write value should always be 0.

Bit 22—EtherC States Register Interrupt (ECI): Indicates that an interrupt due to an EtherC status
register (ECSR) source has been detected.

Bit 22: ECI

Description

0

EtherC status interrupt source not detected

(Initial value)

1

EtherC status interrupt source detected (interrupt source)

Note: EESR is a read-only register. When this register is cleared by a source in ECSR in the

EtherC, this bit is also cleared.

Bit 21—Frame Transmit Complete (TC): Indicates that all the data specified by the transmit
descriptor has been transmitted to the EtherC. The transfer status is written back to the relevant
descriptor. When 1-frame transmission is completed for 1-frame/1-buffer processing, or when the
last data in the frame is transmitted and the transmission descriptor valid bit (TACT) in the next
descriptor is not set for multiple-frame buffer processing, transmission is completed and this bit is
set to 1. After frame transmission, the E-DMAC writes the transmission status back to the
descriptor.

Bit 21: TC

Description

0

Transfer not complete, or no transfer directive

(Initial value)

1

Transfer complete (interrupt source)

Note: As data is sent onto the line by the PHY-LSI from the EtherC via the MII, the actual

transmission completion time is longer.

Bit 20—Transmit Descriptor Exhausted (TDE): Indicates that the transmission descriptor valid bit
(TACT) in the descriptor is not set when the E-DMAC reads the transmission descriptor when the
previous descriptor is not the last one of the frame for multiple- buffer frame processing. As a
result, an incomplete frame may be transmitted.

Bit 20: TDE

Description

0

“1” transmit descriptor active bit (TACT) detected

(Initial value)

1

“0” transmit descriptor active bit (TACT) detected (interrupt source)

Note: When transmission descriptor empty (TDE = 1) occurs, execute a software reset and initiate

transmission. In this case, the address that is stored in the transmit descriptor list address
register (TDLAR) is transmitted first.

«
...
451
452
453
454
455
...
»

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

Brand: F5 Pages: 2

Brand: F5 Pages: 90

Brand: F5 Pages: 47

ROADRECORDER 8000

Brand: Safety Vision Pages: 40

Brand: Velopex Pages: 7

SUPERLOADER DLT MAGAZINE

Brand: Tandberg Data Pages: 6

IPAM-1600s Series

Brand: C-Com Pages: 148

Brand: red lion Pages: 5

Turbo NAS TVS-71 Series

Brand: QNAP Pages: 51

Brand: Longshine Pages: 35

Brand: IFM Electronic Pages: 14

Accelero TWIN TURBO II

Brand: Arctic Pages: 2

Serial Attached SCSI (SAS) Expander Card

Brand: Adaptec Pages: 26

Brand: FOR-A Pages: 37

Brand: ADC Pages: 29

Brand: Brickcom Pages: 184

Brand: Telit Wireless Solutions Pages: 79

Brand: LevelOne Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands