manualshive.com logo in svg

Renesas SH7616, Hardware Manual

The Renesas SH7616 is a high-performance microcontroller, equipped with advanced features for seamless functionality. Unlock its full potential by accessing the comprehensive Hardware Manual. Easily available for free download at manualshive.com, this manual provides detailed instructions and insights, enabling users to maximize the capabilities of this exceptional product.

Share
Download
background image

Section 8   Cache

Rev. 2.00  Mar 09, 2006  page 360 of 906
REJ09B0292-0200

Bit 1—Instruction Replacement Disable Bit (ID): ID is the bit for disabling instruction
replacement. When this bit is 1, an instruction fetched from external memory is not written to the
cache even if there is a cache miss. Cache data is, however, read or updated during cache hits. ID
is valid only when CE is 1.

Bit 1:  ID

Description

0

Normal operation 

(Initial value)

1

Data not replaced even when cache miss occurs in instruction fetch

Bit 0—Cache Enable Bit (CE): CE is the cache enable bit. Cache can be used when CE is set to 1.

Bit 0:  CE

Description

0

Cache disabled

(Initial value)

1

Cache enabled

8.3

Address Space and the Cache

The address space is divided into six partitions. The cache access operation is specified by
addresses. Table 8.2 lists the partitions and their cache operations. For more information on
address spaces, see section 7, Bus State Controller. Note that the spaces of the cache area and
cache-through area are the same.

Table 8.2

Address Space and Cache Operation

Addresses
A31–A29

Partition

Cache Operation

000

Cache area

Cache is used when the CE bit in CCR is 1

001

Cache-through area

Cache is not used

010

Associative purge area

Cache line of the specified address is purged
(disabled)

011

Address array read/write area

Cache address array is accessed directly

110

Data array read/write area

Cache data array is accessed directly

111

I/O area

Cache is not used

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

Canon C50FSi - VB Network Camera Setup Manual preview
C50FSi - VB Network Camera
Brand: Canon Pages: 32
Rabbit 2000 Reference Manual preview
2000
Brand: Rabbit Pages: 120
Acconeer A111 User Manual preview
A111
Brand: Acconeer Pages: 32
Moxa Technologies UC-8100 Series Hardware User Manual preview
UC-8100 Series
Brand: Moxa Technologies Pages: 19
e-con Systems ACC-CX3RDK-CU5640 Getting Started Manual preview
ACC-CX3RDK-CU5640
Brand: e-con Systems Pages: 9
Xilica Audio Design XP 4080 User Manual preview
XP 4080
Brand: Xilica Audio Design Pages: 30
Thermalright AXP-100H MUSCLE Manual preview
AXP-100H MUSCLE
Brand: Thermalright Pages: 36
Cypress Semiconductor CY7C1329H Specification Sheet preview
CY7C1329H
Brand: Cypress Semiconductor Pages: 16
Dahua D-NVR4108HS-4KS2/L Quick Start Manual preview
D-NVR4108HS-4KS2/L
Brand: Dahua Pages: 33
CNC4PC C52- ESS User Manual preview
C52- ESS
Brand: CNC4PC Pages: 11
Zigen IP-Logic ZIG-IPPRO-RX Quick Start Manual preview
IP-Logic ZIG-IPPRO-RX
Brand: Zigen Pages: 4
Hanwha Techwin Wisenet XRN-6410RB2-24TB User Manual preview
Wisenet XRN-6410RB2-24TB
Brand: Hanwha Techwin Pages: 124
Xyclop XC-16CH-NVR-4TB Quick Start Manual preview
XC-16CH-NVR-4TB
Brand: Xyclop Pages: 19
Patton electronics 593/45 User Manual preview
593/45
Brand: Patton electronics Pages: 8
LevelOne WBA-4000 User Manual preview
WBA-4000
Brand: LevelOne Pages: 49
ICS ELECTRONICS VXI-5501 Quick Start Manual preview
VXI-5501
Brand: ICS ELECTRONICS Pages: 4
Idis DR-8364F Quick Manual preview
DR-8364F
Brand: Idis Pages: 16
Boser HS-2621 Manual preview
HS-2621
Brand: Boser Pages: 54

Brands by name

Popular brands

Load more brands