manualshive.com logo in svg

Renesas SH7616, Hardware Manual

The Renesas SH7616 is a high-performance microcontroller, equipped with advanced features for seamless functionality. Unlock its full potential by accessing the comprehensive Hardware Manual. Easily available for free download at manualshive.com, this manual provides detailed instructions and insights, enabling users to maximize the capabilities of this exceptional product.

Share
Download
background image

Section 7   Bus State Controller (BSC)

Rev. 2.00  Mar 09, 2006  page 258 of 906
REJ09B0292-0200

Bit 11—Area 0 Burst ROM Enable (BSTROM)

Bit 11:  BSTROM

Description

0

Area 0 is accessed normally

(Initial value)

1

Area 0 is accessed as burst ROM

Bit 10—Reserved: This bit is always read as 0. The write value should always be 0.

Bits 9 and 8—Long Wait Specification for Areas 2 and 3 (AHLW1, AHLW0): When the basic
memory interface setting is made for CS2 and CS3, from 3 to 14 wait cycles are inserted in CS2 or
CS3 accesses when the bits specifying the respective area waits in the wait control bits (W21,
W20 or W31, W30) in wait control register 1 (WCR1) are set as long waits (i.e., are set to 11) (see
table 7.4).

Bits 7 and 6—Long Wait Specification for Area 1 (A1LW1, A1LW0): From 3 to 14 wait cycles
are inserted in area 1 accesses when the wait control bits (W11, W10) in wait control register 1
(WCR1) are set as long wait (i.e., are set to 11) (see table 7.4).

Bits 5 and 4—Long Wait Specification for Area 0 (A0LW1, A0LW0): When the basic memory
interface setting is made for CS0, from 3 to 14 wait cycles are inserted in CS0 accesses when the
wait control bits (W01, W00) in wait control register 1 (WCR1) are set as long wait (i.e., are set to
11) (see table 7.4).

Bit 3—Endian Specification for Area 4 (A4ENDIAN): In big-endian mode, the most significant
byte (MSB) is the lowest byte address, and byte data is aligned in order toward the least significant
byte (LSB). In little-endian mode, the LSB is the lowest byte address, and byte data is aligned in
order toward the MSB. When this bit is set to 1, data in read/write accesses to the CS4 space is
rearranged into little endian order before being transferred. This is used for data exchange with a
little-endian processor or when executing a program written with awareness of little-endian mode.

Bit 3:  A4ENDIAN

Description

0

Big endian

(Initial value)

1

Little endian

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

Eaton INDGW-X2 Manual preview
INDGW-X2
Brand: Eaton Pages: 10
STONEFLY DR365V-2404 Setup Manual preview
DR365V-2404
Brand: STONEFLY Pages: 48
Multitech MultiConnect SE MTS2EA Quick Start Manual preview
MultiConnect SE MTS2EA
Brand: Multitech Pages: 8
Seattle Computer Products 8086 CPU Instruction Manual preview
8086 CPU
Brand: Seattle Computer Products Pages: 31
C&T Solution RCO-3000 Series User Manual preview
RCO-3000 Series
Brand: C&T Solution Pages: 96
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Brand: C-Com Pages: 148
ivideon Bridge B1610 Quick Start Manual preview
Bridge B1610
Brand: ivideon Pages: 11
PaloAlto Networks ION 1000 Hardware Reference Manual preview
ION 1000
Brand: PaloAlto Networks Pages: 28
AMD Geode LX 800 User Manual preview
Geode LX 800
Brand: AMD Pages: 27
EXAGATE SYSGuard 6001 Quick Installation Manual preview
SYSGuard 6001
Brand: EXAGATE Pages: 7
Mod Duo X User Manual preview
Duo X
Brand: Mod Pages: 11
Spectrum Digital XDS510USB Installation Manual preview
XDS510USB
Brand: Spectrum Digital Pages: 11
ST ST7-EMU3 Series User Manual preview
ST7-EMU3 Series
Brand: ST Pages: 39
Intel 80C186EC Manual preview
80C186EC
Brand: Intel Pages: 57
Ecolab EcoJet EcoStar 1500 Installation & Operation Manual preview
EcoJet EcoStar 1500
Brand: Ecolab Pages: 80
Motorola MC68VZ328 User Manual preview
MC68VZ328
Brand: Motorola Pages: 376
Motorola MC68341 User Manual preview
MC68341
Brand: Motorola Pages: 20
MSI CB11B Quick Start preview
CB11B
Brand: MSI Pages: 3

Brands by name

Popular brands

Load more brands