manualshive.com logo in svg

Renesas SH7616, Hardware Manual

The Renesas SH7616 is a high-performance microcontroller, equipped with advanced features for seamless functionality. Unlock its full potential by accessing the comprehensive Hardware Manual. Easily available for free download at manualshive.com, this manual provides detailed instructions and insights, enabling users to maximize the capabilities of this exceptional product.

Share
Download
background image

Section 17   16-Bit Timer Pulse Unit (TPU)

Rev. 2.00  Mar 09, 2006  page 681 of 906

REJ09B0292-0200

Section 17   16-Bit Timer Pulse Unit (TPU)

17.1

Overview

An on-chip 16-bit timer pulse unit (TPU) is provided that comprises three 16-bit timer channels.

17.1.1

Features

The TPU has the following features:

•

 

Maximum 8-pulse input/output

•

 

A total of eight timer general registers (TGRs) are provided (four for channel 0 and two each
for channels 1, and 2).

 

Each register can be set independently as an output compare/input capture register.

 

TGRC and TGRD for channel 0 can be used as buffer registers

•

 

Choice of seven or eight counter input clocks for each channel

•

 

The following operations can be set for each channel:

 

Waveform output by compare match: Selection of 0, 1, or toggle output

 

Input capture function: Choice of rising edge, falling edge, or both edge detection

 

Counter clear operation: Counter clearing possible by compare match or input capture

 

Synchronous operation: Multiple timer counters (TCNT) can be written to simultaneously
simultaneous clearing by compare match and input capture possible
register simultaneous input/output possible by counter synchronous operation

 

PWM mode: Any PWM output duty can be set maximum of 7-phase PWM output possible
by combination with synchronous operation

•

 

Buffer operation settable for channel 0

 

Input capture register double-buffering possible

 

Automatic rewriting of output compare register possible

•

 

Phase counting mode settable independently for each of channels 1, and 2

 

Two-phase encoder pulse up/down-count possible

•

 

Fast access via internal 16-bit bus

 

Fast access is possible via a 16-bit bus interface

•

 

13 interrupt sources

 

For channel 0 four compare match/input capture dual-function interrupts and one overflow
interrupt can be requested independently

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

EAW MX8600 Jumpstart Manual preview
MX8600
Brand: EAW Pages: 6
EAW UX8800 Technical Note preview
UX8800
Brand: EAW Pages: 6
Sangoma A400 Installation Manual preview
A400
Brand: Sangoma Pages: 6
Paradox ZX32D Manual preview
ZX32D
Brand: Paradox Pages: 4
Salusfin SF-930EU User'S Installation Manual preview
SF-930EU
Brand: Salusfin Pages: 6
Avolites Titan One Quick Start Manual preview
Titan One
Brand: Avolites Pages: 24
ESD ECS-CPCIs/FPGA Hardware Manual preview
ECS-CPCIs/FPGA
Brand: ESD Pages: 28
peplink balance ONE Manual preview
balance ONE
Brand: peplink Pages: 2
OpenVox B800P User Manual preview
B800P
Brand: OpenVox Pages: 13
ICOP Technology Vortex86SX VSX-6100 User Manual preview
Vortex86SX VSX-6100
Brand: ICOP Technology Pages: 50
VCS VIP 1000 User Manual preview
VIP 1000
Brand: VCS Pages: 118
Observint NVR16 Firmware User Manual preview
NVR16
Brand: Observint Pages: 117
ADS Technologies API-800 Installation Manual preview
API-800
Brand: ADS Technologies Pages: 21
ST STA309A Operation Manual preview
STA309A
Brand: ST Pages: 67
Net Optics Phantom HD Quick Install Manual preview
Phantom HD
Brand: Net Optics Pages: 2
Carrier 40VMW005 Installation And Maintenance Instructions Manual preview
40VMW005
Brand: Carrier Pages: 18
Qvis 72-8P Series User Manual preview
72-8P Series
Brand: Qvis Pages: 233
Cooler Master MCY-C3P1-KWNN Manual preview
MCY-C3P1-KWNN
Brand: Cooler Master Pages: 4

Brands by name

Popular brands

Load more brands