manualshive.com logo in svg

Renesas SH7616, Hardware Manual

The Renesas SH7616 is a high-performance microcontroller, equipped with advanced features for seamless functionality. Unlock its full potential by accessing the comprehensive Hardware Manual. Easily available for free download at manualshive.com, this manual provides detailed instructions and insights, enabling users to maximize the capabilities of this exceptional product.

Share
Download
background image

Section 11   Direct Memory Access Controller (DMAC)

Rev. 2.00  Mar 09, 2006  page 469 of 906

REJ09B0292-0200

Bits 11 and 10—Transfer Size Bits (TS1, TS0): Select the DMA transfer size. When 11 is set to
bits TS1 and TS0 (in the 16-byte unit), request mode is available only in auto-request mode and at
edge detection in external request mode. When 11 is set to bits TS1 and TS0 (in the 16-byte unit)
and level detection in external request mode and internal peripheral-module request mode are set,
system operations are not guaranteed. TS1 and TS0 are initialized to 00 by a reset and in standby
mode. Values are retained during a module standby.

Bit 11:  TS1

Bit 10:  TS0

Description

0

0

Byte unit

*

(initial value)

1

Word (2-byte) unit

1

0

Longword (4-byte) unit

1

16-byte unit (4 longword transfers)

Note: 

*

The byte unit setting should not be used if a destination address has been set in internal
memory for the dual address mode.

Bit 9—Auto Request Mode Bit (AR): Selects either auto-request mode (in which transfer requests
are generated automatically within the DMAC) or a mode using external requests or requests from
on-chip peripheral modules (SCIF, TPU, SIOF, SIO). The AR bit is initialized to 0 by a reset and
in standby mode. Its value is retained during a module standby.

Bit 9:  AR

Description

0

External/on-chip peripheral module request mode

(Initial value)

1

Auto-request mode

Bit 8—Acknowledge/Transfer Mode Bit (AM): In dual address mode, this bit selects whether the
DACKn signal is output during the data read cycle or write cycle. In single-address mode, it
selects whether to transfer data from memory to device or from device to memory. The AM bit is
initialized to 0 by a reset and in standby mode. Its value is retained during a module standby.

Bit 8:  AM

Description

0

DACKn output in read cycle (dual address mode)/transfer from memory
to device (single address mode)

(Initial value)

1

DACKn output in write cycle (dual address mode)/transfer from device
to memory (single address mode)

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Brand: D-Link Pages: 38
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Brand: D-Link Pages: 6
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Brand: D-Link Pages: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 97
Observint NVR4 Firmware User Manual preview
NVR4
Brand: Observint Pages: 117
Freescale Semiconductor MCF54455 Reference Manual preview
MCF54455
Brand: Freescale Semiconductor Pages: 921
Ericsson Marconi OMS 1200 Product Description preview
Marconi OMS 1200
Brand: Ericsson Pages: 136
Crystal Vision TANDEM HD-21 User Manual preview
TANDEM HD-21
Brand: Crystal Vision Pages: 54
Disc Makers Reflex10 User Manual preview
Reflex10
Brand: Disc Makers Pages: 38
Navitar 1-62645 Dimensional Drawing preview
1-62645
Brand: Navitar Pages: 1
Ubiquiti airMAX NanoBridge M NBM3 Quick Start Manual preview
airMAX NanoBridge M NBM3
Brand: Ubiquiti Pages: 24
Tripp Lite SmartRack SR25UBEXP Specifications preview
SmartRack SR25UBEXP
Brand: Tripp Lite Pages: 4
Ceragon Fibe-Air IP-10G Installation Manual preview
Fibe-Air IP-10G
Brand: Ceragon Pages: 71
Enterasys GPIM-08 Reference Sheet preview
GPIM-08
Brand: Enterasys Pages: 2
Aerotech QNP3 Series Hardware Manual preview
QNP3 Series
Brand: Aerotech Pages: 62
IBASE Technology 11th Gen Intel Core U-Series User Manual preview
11th Gen Intel Core U-Series
Brand: IBASE Technology Pages: 70
Alphacool EISBLOCK AURORA ACRYL GPX-N RTX 3070 VENTUS INCL Instructions preview
EISBLOCK AURORA ACRYL GPX-N RTX 3070 VENTUS INCL
Brand: Alphacool Pages: 3

Brands by name

Popular brands

Load more brands