manualshive.com logo in svg

Renesas SH7616, Hardware Manual

The Renesas SH7616 is a high-performance microcontroller, equipped with advanced features for seamless functionality. Unlock its full potential by accessing the comprehensive Hardware Manual. Easily available for free download at manualshive.com, this manual provides detailed instructions and insights, enabling users to maximize the capabilities of this exceptional product.

Share
Download
background image

Section 7   Bus State Controller (BSC)

Rev. 2.00  Mar 09, 2006  page 317 of 906

REJ09B0292-0200

7.5.8

Refreshes

The bus state controller is equipped with a function to control refreshes of synchronous DRAM.
Auto-refreshes can be performed by setting the RMODE bit to 0 and the RFSH bit to 1 in MCR.
Consecutive refreshes can also be generated by setting the RRC2–RRC0 bits in RTCSR. When the
synchronous DRAM is not accessed for a long period of time, set the RFSH bit and RMODE bit
both to 1 to generate self-refresh mode, which uses low power consumption to retain data.

Auto-Refresh:

 The number of refreshes set in the RRC2–RRC0 bits in RTCSR are performed at

the interval determined by the input clock selected by the CKS2–CKS0 bits in RTCSR and the
value set in RTCOR. Set the CKS2–CKS0 bits and RTCOR so that the refresh interval
specifications of the synchronous DRAM being used are satisfied. First , set RTCOR, RTCNT,
and the RMODE and RFSH bits in MCR, then set the CKS2–CKS0 and RRC2–RRC0 bits in
RTCSR. When a clock is selected with the CKS2–CKS0 bits, RTCNT starts counting up from the
value at that time. The RTCNT value is constantly compared to the RTCOR value, and when the
two values match, a refresh request is made, and the number of auto-refreshes set in RRC2–RRC0
are performed. RTCNT is cleared to 0 at that time and the count up starts again. Figure 7.33 shows
the timing for the auto-refresh cycle.

First, a PALL command is issued during the Tp cycle to change all the banks from active to
precharge states. Then number of idle cycles equal to one less than the value set in TRP1 and
TRP0 are inserted, and a REF command is issued in the Trr cycle. After the Trr cycle, no new
commands are output for the number of cycles specified in the TRAS bit in MCR. The TRAS bit
must be set to satisfy the refresh cycle time specifications (active/active command delay time) of
the synchronous DRAM. When the set value of the TRP1 and TRP0 bits in MCR is 2 or more, an
NOP cycle is inserted between the Tp cycle and Trr cycle.

During a manual reset, no refresh request is issued, since there is no RTCNT count-up. To perform
a refresh properly, make the manual reset period shorter than the refresh cycle interval and set
RTCNT to (RTCOR – 1) so that the refresh is performed immediately after the manual reset is
cleared.

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

Paradyne 3172 Quick Reference preview
3172
Brand: Paradyne Pages: 20
Paradyne Compshere 3000 Series Notice preview
Compshere 3000 Series
Brand: Paradyne Pages: 2
Intel NetStructure ZT 5515 Product Specification preview
NetStructure ZT 5515
Brand: Intel Pages: 90
KEMP Technologies LoadMaster 1500 Installation And Configuration Manual preview
LoadMaster 1500
Brand: KEMP Technologies Pages: 71
Lancom 7100 VPN Manual preview
7100 VPN
Brand: Lancom Pages: 70
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Brand: Buffalo Pages: 2
C&T Solution RCO-3000 Series User Manual preview
RCO-3000 Series
Brand: C&T Solution Pages: 96
Moxa Technologies PT-7324 Series User Manual preview
PT-7324 Series
Brand: Moxa Technologies Pages: 36
Renesas Converter Board R0E521237CFK00 User Manual preview
Converter Board R0E521237CFK00
Brand: Renesas Pages: 6
Alula RE930R LTE M1 Install Manual preview
RE930R LTE M1
Brand: Alula Pages: 4
ADTRAN NetVanta Serial Dial Backup Interface Module (DIM) none Quick Start Manual preview
NetVanta Serial Dial Backup Interface Module (DIM) none
Brand: ADTRAN Pages: 2
UNICORECOMM UM620N User Manual preview
UM620N
Brand: UNICORECOMM Pages: 19
SONIX MP5S Plus Writer Quick Manual preview
MP5S Plus Writer
Brand: SONIX Pages: 23
Galileo Quark SoC X1000 Getting Started Manual preview
Quark SoC X1000
Brand: Galileo Pages: 20
XtendLan XL-VC102SB User Manual preview
XL-VC102SB
Brand: XtendLan Pages: 17
Alcatel-Lucent Broadband 700 MHz Brochure preview
Broadband 700 MHz
Brand: Alcatel-Lucent Pages: 8
Extreme Networks ExtremeCloud Appliance E3120 Installation Manual preview
ExtremeCloud Appliance E3120
Brand: Extreme Networks Pages: 27
Oracle Database Appliance X6-2-HA Deployment And User'S Manual preview
Database Appliance X6-2-HA
Brand: Oracle Pages: 473

Brands by name

Popular brands

Load more brands