manualshive.com logo in svg

Renesas SH7616, Hardware Manual

The Renesas SH7616 is a high-performance microcontroller, equipped with advanced features for seamless functionality. Unlock its full potential by accessing the comprehensive Hardware Manual. Easily available for free download at manualshive.com, this manual provides detailed instructions and insights, enabling users to maximize the capabilities of this exceptional product.

Share
Download
background image

Section 1   Overview

Rev. 2.00  Mar 09, 2006  page 1 of 906

REJ09B0292-0200

Section 1   Overview

1.1

Features of SuperH Microcomputer with On-Chip Ethernet
Controller

The SH7616 is a CMOS single-chip microcontroller that integrates a high-speed CPU core using
an original Renesas architecture with supporting functions required for an Ethernet system.

The CPU has a RISC (Reduced Instruction Set Computer) type instruction set. The CPU basically
operates at a rate of one instruction per cycle, offering a great improvement in instruction
execution speed. In addition, the 32-bit internal architecture provides improved data processing
power, and DSP functions have also been enhanced with the implementation of extended Harvard
architecture DSP data bus functions. With this CPU, it has become possible to assemble low-cost,
high-performance/high-functionality systems even for applications such as realtime control, which
could not previously be handled by microcontrollers because of their high-speed processing
requirements. The SH7616 also includes a maximum 4-kbyte cache, for greater CPU processing
power when accessing external memory.

The SH7616 is equipped with a media access controller (MAC) conforming to the IEEE802.3u
standard, and an Ethernet controller that includes a media independent interface (MII) standard
unit, enabling 10/100 Mbps LAN connection. Supporting functions necessary for system
configuration are also provided, including RAM, timers, a serial communication interface with
FIFO (SCIF), interrupt controller (INTC), and I/O ports.

To improve the efficiency of frame transmission/reception, the processing power of the DMAC for
the Ethernet controller is improved and the FIFO for the DMAC has 2 kbytes. A CAM match
signal input function is provided for systems that require multiple MAC addresses. In serial I/O
with three channels, one operates with the FIFO for better data processing power when connected
to the codec.

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

Mackie SP260 Installation Instructions preview
SP260
Brand: Mackie Pages: 2
Mackie SP260 Product Overview preview
SP260
Brand: Mackie Pages: 5
Farallon NetLINE USB User Manual preview
NetLINE USB
Brand: Farallon Pages: 26
Observint N16 Quick Setup Manual preview
N16
Brand: Observint Pages: 11
F5 i5000 Series Platform Manual preview
i5000 Series
Brand: F5 Pages: 72
A10 Thunder Series Manual preview
Thunder Series
Brand: A10 Pages: 52
NEC P401-TMX4D User Manual preview
P401-TMX4D
Brand: NEC Pages: 2
Telex Communications 2472AA Instruction Manual preview
2472AA
Brand: Telex Communications Pages: 28
Grizzly PSJ-M3 GEN2 User Manual preview
PSJ-M3 GEN2
Brand: Grizzly Pages: 9
XtendLan XL-HCW224C User Manual preview
XL-HCW224C
Brand: XtendLan Pages: 52
Gundermann VIDEOWALL LEDWALL Optimizer HQ P2 Manual preview
LEDWALL Optimizer HQ P2
Brand: Gundermann VIDEOWALL Pages: 12
FiberHome AN5506-04-F User Manual preview
AN5506-04-F
Brand: FiberHome Pages: 2
Thermaltake Extreme Spirit Il Instruction preview
Extreme Spirit Il
Brand: Thermaltake Pages: 2
Pilz PNOZ mc3p Operating Instructions Manual preview
PNOZ mc3p
Brand: Pilz Pages: 12
Renesas Emulation Memory Board R0E330850MSRC0 User Manual preview
Emulation Memory Board R0E330850MSRC0
Brand: Renesas Pages: 4
H3C SecPath L5030 Installation Manual preview
SecPath L5030
Brand: H3C Pages: 62
Z3 Technology FSDI-1XA User Manual preview
FSDI-1XA
Brand: Z3 Technology Pages: 83
M86 Security Web Filter HL User Manual preview
Web Filter HL
Brand: M86 Security Pages: 512

Brands by name

Popular brands

Load more brands