manualshive.com logo in svg

Renesas SH7616, Hardware Manual

The Renesas SH7616 is a high-performance microcontroller, equipped with advanced features for seamless functionality. Unlock its full potential by accessing the comprehensive Hardware Manual. Easily available for free download at manualshive.com, this manual provides detailed instructions and insights, enabling users to maximize the capabilities of this exceptional product.

Share
Download
background image

Section 21   Power-Down Modes

Rev. 2.00  Mar 09, 2006  page 805 of 906

REJ09B0292-0200

21.3

Sleep Mode

21.3.1

Transition to Sleep Mode

Executing the SLEEP instruction when the SBY bit in SBYCR1 is 0 causes a transition from the
program execution state to sleep mode. Although the CPU halts immediately after executing the
SLEEP instruction, the contents of its internal registers remain unchanged. The on-chip peripheral
modules continue to run in sleep mode.

21.3.2

Canceling Sleep Mode

Sleep mode is canceled by an interrupt, DMA address error, power-on reset, or manual reset.

Cancellation by an Interrupt:

 When an interrupt occurs, sleep mode is canceled and interrupt

exception handling is executed. Sleep mode is not canceled if the interrupt cannot be accepted
because its priority level is equal to or less than the mask level set in the CPU’s status register
(SR) or if an interrupt by an on-chip peripheral module is disabled at the peripheral module.

Cancellation by a DMA Address Error:

 If a DMA address error occurs, sleep mode is canceled

and DMA address error exception handling is executed.

Cancellation by a Power-On Reset:

 A power-on reset cancels sleep mode.

Cancellation by a Manual Reset:

 A manual reset cancels sleep mode.

21.4

Standby Mode

21.4.1

Transition to Standby Mode

To enter standby mode, set the SBY bit to 1 in SBYCR1, then execute the SLEEP instruction. The
chip switches from the program execution state to standby mode. The NMI interrupt cannot be
accepted when the SLEEP instruction is executed, or for the following five cycles. In standby
mode, the clock supply to all on-chip peripheral modules is halted as well as the CPU. CPU
register contents are held, and some on-chip peripheral modules are initialized.

Summary of Contents for SH7616








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7616

3Com 486 Getting Started Manual preview
486
Brand: 3Com Pages: 20
BSS Audio EC-4B Installation Manual preview
EC-4B
Brand: BSS Audio Pages: 20
Reeven NAIA Installation Manual preview
NAIA
Brand: Reeven Pages: 2
Hama HDD Silenser Bedienungsanleitung preview
HDD Silenser
Brand: Hama Pages: 12
TP-Link VIGI NVR1008 Quick Installation Manual preview
VIGI NVR1008
Brand: TP-Link Pages: 2
Sennheiser Surround Dongle User Manual preview
Surround Dongle
Brand: Sennheiser Pages: 18
Sangoma A200 Analog Installation Manual preview
A200 Analog
Brand: Sangoma Pages: 6
PMD DK55110 Manual preview
DK55110
Brand: PMD Pages: 74
AMD Geode LE-366 User Manual preview
Geode LE-366
Brand: AMD Pages: 45
Acromag ACPS3320 User Manual preview
ACPS3320
Brand: Acromag Pages: 35
Cypress Semiconductor CY8C24223A Specification Sheet preview
CY8C24223A
Brand: Cypress Semiconductor Pages: 31
LaView LV-KN series Quick Start Manual preview
LV-KN series
Brand: LaView Pages: 2
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Brand: Vivint Pages: 2
SIIG SATA II-150 PCI Quick Installation Manual preview
SATA II-150 PCI
Brand: SIIG Pages: 16
SilverStone EXB02 Manual preview
EXB02
Brand: SilverStone Pages: 12
Sennheiser GSP 300 User Manual preview
GSP 300
Brand: Sennheiser Pages: 22
Akasa Venom A10 User Manual preview
Venom A10
Brand: Akasa Pages: 2
Dahua Technology VDA-NVR2108W4KS2 User Manual preview
VDA-NVR2108W4KS2
Brand: Dahua Technology Pages: 363

Brands by name

Popular brands

Load more brands