manualshive.com logo in svg

Renesas H8S/2100 Series, Hardware Manual

The Renesas H8S/2100 Series is a high-performance microcontroller designed for a wide range of industrial and automotive applications. For comprehensive instructions on how to utilize its features, download the free Hardware Manual from manualshive.com. Get detailed guidance and insights to maximize the potential of this powerful product.

Share
Download
background image

Section 3   MCU Operating Modes 

 

 

Rev. 1.00  Apr. 28, 2008  Page 67 of 994 

 

 REJ09B0452-0100 

Section 3   MCU Operating Modes 

3.1 Operating 

Mode 

Selection 

This LSI supports three operating modes (modes 2, 4, and 6). The operating mode is determined 
by the setting of the mode pins (MD2 and MD1). Table 3.1 shows the MCU operating mode 
selection. 

Table 3.1 

MCU Operating Mode Selection 

MCU Operating 
Mode MD2 

MD1 

MD0

*

 

CPU Operating 
Mode Description  On-Chip 

ROM

2 0 

1 

0 

Advanced 

Single-chip 

mode 

Enabled 

4 1 

0 

0 

 Flash 

memory 

programming/erasing 

 

6 

1 

1 

0 

Emulation 

On-chip emulation mode  Enabled 

Note: 

*

  MD0 is not available as a pin and is internally fixed to 0. 

 

Modes 2 is single-chip mode. 

Modes 0, 1, 3, 5 and 7 are not available in this LSI. Modes 4 and 6 are operating modes for a 
special purpose. Thus, mode pins should be set to enable mode 2 in the normal program execution 
state. Mode pin settings should not be changed during operation. After a reset is canceled, the 
mode pin inputs should be latched by reading MDCR. 

Mode 4 is a boot mode for programming or erasing the flash memory. For details, see section 24, 
Flash Memory. 

Mode 6 is an on-chip emulation mode. In this mode, this LSI is controlled by an on-chip emulator 
(E10A) via the JTAG, thus enabling on-chip emulation. 

Summary of Contents for H8S/2100 Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2100 Series

Udoo NEO Step-By-Step Manual preview
NEO
Brand: Udoo Pages: 7
FabiaTech FX5638 Series Users Quick Reference preview
FX5638 Series
Brand: FabiaTech Pages: 4
National Instruments NI 5922 Calibration Procedure preview
NI 5922
Brand: National Instruments Pages: 28
National Instruments NI 9219 Getting Started preview
NI 9219
Brand: National Instruments Pages: 19
National Instruments NI 6711 User Manual preview
NI 6711
Brand: National Instruments Pages: 103
National Instruments NI PXI-1042 Series Installation Manual preview
NI PXI-1042 Series
Brand: National Instruments Pages: 12
National Instruments PCI-1407 Setup And Operation preview
PCI-1407
Brand: National Instruments Pages: 4
Xilica Audio Design neutrino series Quick Start Manual preview
neutrino series
Brand: Xilica Audio Design Pages: 26
Tripp Lite N48M Series Installation Manual preview
N48M Series
Brand: Tripp Lite Pages: 20
Oracle Talari E1000 Installation Manual preview
Talari E1000
Brand: Oracle Pages: 24
Ubiquiti PBE-5AC-300-ISO Quick Start Manual preview
PBE-5AC-300-ISO
Brand: Ubiquiti Pages: 28
Advantech ARK-1380 User Manual preview
ARK-1380
Brand: Advantech Pages: 50
Rane HAL1x System Installation Manual preview
HAL1x
Brand: Rane Pages: 128
Acard AEC-6885 User Manual preview
AEC-6885
Brand: Acard Pages: 34
Shure DFR22 Software Manual preview
DFR22
Brand: Shure Pages: 113
Segger J-Link-OB-STM32F072-128KB User Manual preview
J-Link-OB-STM32F072-128KB
Brand: Segger Pages: 18
Seagate CHEETAH ST34501FC Product Manual preview
CHEETAH ST34501FC
Brand: Seagate Pages: 68
ADTRAN NetVanta Serial Dial Backup Interface Module (DIM) none Quick Start Manual preview
NetVanta Serial Dial Backup Interface Module (DIM) none
Brand: ADTRAN Pages: 2

Brands by name

Popular brands

Load more brands