manualshive.com logo in svg

Freescale Semiconductor MC9S12ZVM series, Reference Manual

Share
Download
Freescale Semiconductor MC9S12ZVM series Reference Manual Download Page 52

Chapter 1 Device Overview MC9S12ZVM-Family

MC9S12ZVM Family Reference Manual  Rev. 1.3

52

Freescale Semiconductor

NOTE

Please refer to the Flash block description for more security byte details.

1.10.3

Operation of the Secured Microcontroller

By securing the device, unauthorized access to the EEPROM and Flash memory contents is prevented.
Secured operation has the following effects on the microcontroller:

1.10.3.1

Normal Single Chip Mode (NS)

•

Background debug controller (BDC) operation is completely disabled.

•

Execution of Flash and EEPROM commands is restricted (described in flash block description).

1.10.3.2

Special Single Chip Mode (SS)

•

Background debug controller (BDC) commands are restricted

•

Execution of Flash and EEPROM commands is restricted (described in flash block description).

In special single chip mode the device is in active BDM after reset. In special single chip mode on a secure
device, only the BDC mass erase and BDC control and status register commands are possible. BDC access
to memory mapped resources is disabled. The BDC can only be used to erase the EEPROM and Flash
memory without giving access to their contents.

1.10.4

Unsecuring the Microcontroller

Unsecuring the microcontroller can be done using three different methods:

1. Backdoor key access

2. Reprogramming the security bits

3. Complete memory erase

1.10.4.1

Unsecuring the MCU Using the Backdoor Key Access

In normal single chip mode, security can be temporarily disabled using the backdoor key access method.
This method requires that:

•

The backdoor key has been programmed to a valid value

•

The KEYEN[1:0] bits within the Flash options/security byte select ‘enabled’.

•

The application program programmed into the microcontroller has the capability to write to the
backdoor key locations

The backdoor key values themselves would not normally be stored within the application data, which
means the application program would have to be designed to receive the backdoor key values from an
external source (e.g. through a serial port)

The backdoor key access method allows debugging of a secured microcontroller without having to erase
the Flash. This is particularly useful for failure analysis.

Summary of Contents for MC9S12ZVM series


























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands