manualshive.com logo in svg

Freescale Semiconductor MC9S12ZVM series, Reference Manual

Share
Download
Freescale Semiconductor MC9S12ZVM series Reference Manual Download Page 21

Chapter 1 Device Overview MC9S12ZVM-Family

MC9S12ZVM Family Reference Manual Rev. 1.3

Freescale Semiconductor

21

•

Autonomous periodic interrupt (API)

•

20mA high-current output for use as Hall sensor supply

•

Supply voltage sense with low battery warning

•

Chip temperature sensor

1.4

Module Features

The following sections provide more details of the integrated modules.

1.4.1

S12Z Central Processor Unit (CPU)

The S12Z CPU is a revolutionary high-speed core, with code size and execution efficiencies over the S12X
CPU. The S12Z CPU also provides a linear memory map eliminating the inconvenience and performance
impact of page swapping.

•

Harvard Architecture - parallel data and code access

•

3 stage pipeline

•

32-Bit wide instruction and databus

•

32-Bit ALU

•

24-bit addressing, of 16MB linear address space

•

Instructions and Addressing modes optimized for C-Programming & Compiler

•

Optimized address path so it is capable to run at 50MHz without Flash wait states

— MAC unit 32bit += 32bit*32bit

— Hardware divider

— Single cycle multi-bit shifts (Barrel shifter)

— Special instructions for fixed point math

•

Unimplemented opcode traps

•

Unprogrammed byte value (0xFF) defaults to SWI instruction

1.4.1.1

Background Debug Controller (BDC)

•

Background debug controller (BDC) with single-wire interface

— Non-intrusive memory access commands

— Supports in-circuit programming of on-chip nonvolatile memory

1.4.1.2

Debugger (DBG)

•

Enhanced DBG module including:

— Four comparators (A, B, C and D) each configurable to monitor PC addresses or addresses of

data accesses

— A and C compare full address bus and full 32-bit data bus with data bus mask register

— B and D compare full address bus only

Summary of Contents for MC9S12ZVM series


























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands