manualshive.com logo in svg

Freescale Semiconductor MC9S12ZVM series, Reference Manual

Share
Download
Freescale Semiconductor MC9S12ZVM series Reference Manual Download Page 26

Chapter 1 Device Overview MC9S12ZVM-Family

MC9S12ZVM Family Reference Manual  Rev. 1.3

26

Freescale Semiconductor

•

Programmers model with list based command and result storage architecture
ADC directly writes results to RAM, preventing stall of further conversions

•

Internal signals monitored with the ADC module

— VRH, VRL, (VRL+VRH)/2, Vsup monitor, Vbg, TempSense, GDU phase, GDU DC-link

•

External pins can also be used as digital I/O

1.4.13

Supply Voltage Sensor (BATS)

•

Monitoring of supply (VSUP) voltage

•

Internal ADC interface from an internal resistive divider

•

Generation of low or high voltage interrupts

1.4.14

On-Chip Voltage Regulator system (VREG)

•

Voltage regulator

— Linear voltage regulator directly supplied by VSUP

— Low-voltage detect on VSUP

— Power-on reset (POR)

— Low-voltage reset (LVR) for VDDX domain

— External ballast device support to reduce internal power dissipation

— Capable of supplying both the MCU internally plus external components

— Over-temperature interrupt

•

Internal voltage regulator

— Linear voltage regulator with bandgap reference

— Low-voltage detect on VDDA

— Power-on reset (POR) circuit

— Low-voltage reset for VDD domain

•

Package option for VREG ballast control output to supply external CANPHY

1.4.15

Gate Drive Unit (GDU)

•

Low side and high side FET pre-drivers for each phase

•

Gate drive pre-regulator LDO (Low Dropout Voltage Regulator)

•

High side gate supply done via bootstrap circuit with external diode and capacitor

•

Sustaining charge pump with two external capacitors and diodes

•

Optional boost convertor configuration with voltage feedback

•

FET-Predriver desaturation and error recognition

•

Monitoring of FET High Side drain (HD) voltage

•

Diagnostic failure management

Summary of Contents for MC9S12ZVM series


























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands