manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 662

Index

650

FTB-700G/800 Series

M

M0 .................................................... 491, 494
M1 .................................................... 491, 494
MA Name.................................................. 223
MAC .......................................................... 205
MAC Address............................. 185, 223, 224
MAC/IP/UDP............................................... 172
MAID......................................................... 223
maintenance

front panel .......................................... 565
general information............................. 565

Manual.............................. 150, 346, 409, 477
Manual Loopback Status........................... 423
Margin ...................................................... 213
Mask

Filter .................................................... 474

Matching & Swapping............................... 262
Max Hop Count......................................... 503
Max Jitter .................................................. 239
Max Latency ...................................... 239, 407
Max Offset ................................................ 420
Max Rate ........................................... 346, 409
Max Round Trip Time ................................ 505
Max Round-Trip Latency............................ 239
Max RX Power ................................... 155, 241
Max RX Rate.............................................. 407
Max TX Rate .............................................. 271
Max. (-/+) Offset ....................................... 437
Max. Jitter ................................................. 407
Max. Negative Offset................................. 245
Max. Offset ............................................... 157
Max. Positive Offset................................... 245
Max. Rate .......................................... 209, 212
Maximum.................................................. 291
Maximum OAMPDU Size ........................... 358
Maximum Window Size............................. 278
MD Level ................................................... 224
Measure Delay button............................... 517
Mechanism................................................ 112
MEF........................................................... 220
MEG ID...................................................... 223

MEG Level.......................................... 224, 347
MEP ID....................................................... 224
Message Rate ............................................ 113
Message Type ............................................ 352
Metrics ...................................................... 386
MFAS................................................. 323, 481
Mid-Trigger ............................................... 478
Min Round Trip Time ................................. 505
Min RX Power.................................... 155, 241
Minimum................................................... 291
Minimum RTT .................................... 413, 428
Minimum Window Size ............................. 278
Mismatch ’0’ ............................................. 297
Mismatch ’1’ ............................................. 297
Mismerge .................................................. 326
Mixed ........................................................ 173
Mode......................... 112, 262, 346, 467, 516
Modify DS0................................................ 249
Modify E0.................................................. 249
Modify Frame Structure............................. 173
Modify Loop Codes ........................... 253, 255
Modify Structure ......................................... 95

Ethernet Test Applications ................... 103
Packet Sync Test Applications ...... 108, 109
Transport Test Applications.................... 97
Wireless Test Applications.................... 110

Modify Structure button.............................. 97
MON.......................................................... 127
Monetary Cost........................................... 183
MPLS ................................................. 177, 364
MPLS Label ................................................ 174
MPLS-TP Label Stack .................................. 225
MPLS-TP Mode .......................................... 225
MPLS-TP OAM............ 107, 220, 326, 358, 379

Traffic .................................................. 451

MPLS-TP OAM Responder .......................... 221
MS............................................................. 330
MS-AIS....................................................... 330
MS-RDI ...................................................... 331
MS-REI....................................................... 331
MS-REI Computation Method.................... 259
MTU .................................................. 413, 428

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands