manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 207

Test Setup - Test Configurator, Timer, and System

NetBlazer

195

Network Details (iSAM)

Frame Size 

The following table lists each component that may affect the 
minimum frame size value. 

Note:

Sending traffic with frame size > 1518 in switched network may results in 
losing theses frames.

Type

Frame Size (bytes)

Fixed

 (default)

64

a

 (default) to 16000

b

a.

The minimum value is adjusted according to the frame structure and

components selected as shown in the following table. 

b.

The maximum frame size is limited to 10000 for 10/100/1000Mbps electrical

interface. 

EMIX

64

a

 to 16000

b

Component

Description

C-VLAN

4 bytes

UDP

8 bytes

Ethernet Header

14 bytes

IPv4

20 bytes

Using DTS

4 bytes

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands