EXFO FTB-1 User Manual Download Page 402

Page: 402 / 675

Test Results

390

FTB-700G/800 Series

Streams - Throughput

Streams - Throughput

From the

Test

menu, tap

Results

Streams

, and the

Throughput

tab.



Stream

indicates the stream identification number.



TX Rate

indicates the transmitted throughput rate.



RX Rate

is measured for each stream on all valid frames (valid

Throughput tag with no FCS error).

Current

Average

Minimum

, and

Maximum

throughput results are reported. Refer to

Unit

on page 265

for unit selection.

Note:

Current

value of

indicates that no RX rate has been measured in the

last second.



Total

indicates the total TX and current measured RX throughput of all

valid frames (valid Throughput tag with no FCS error).



Thresholds

button allows to set the pass/fail thresholds (refer to

QoS

Metrics

on page 272).

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands

EXFO FTB-1, User Manual

Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands