manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 131

Test Setup - Test Configurator, Timer, and System

NetBlazer

119

BERT

Invert

 check box, when selected (cleared by default), inverts the test 

pattern meaning that every 0 will be changed for 1 and every 1 for 0. 
For example, the pattern 1100 will be sent as 0011. Not available when 
pattern is Multi-Pattern. 

Bit Error

Pass/Fail Verdict

 allows to enable bit-error-rate pass/fail verdict by 

selecting either 

Bit Error Count

 or 

Bit Error Rate

. The default value is 

Disabled

. 

BER Threshold

 allows to enter the threshold 

Count

 or 

Rate 

value that 

will be used to declare the pass/fail verdict. The 

BER Threshold

 

applies to individual pattern for 

Multi-Pattern

. 

For 

Count

, enter the maximum bit error count allowed before 

declaring a fail verdict: 

0

 (default) to 

999999

.

For 

Rate

, enter the maximum bit error rate allowed before declaring a 

fail verdict: 

1.0E-14

 to 

1.9E-01

. The default value is 

1.0E-12

.

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands