manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 83

Test Setup - Test Applications

NetBlazer

71

CPRI/OBSAI BERT

Typical CPRI/OBSAI BERT test applications: 

1 Note that a RRH is typically not capable to perform a loopback of the traffic so BERT test monitoring is not applicable. 

The BERT test is more common when testing between two test units. 

Supported Interfaces/Rates: 
CPRI: 1.2, 2.4, 3.1, 4.9, 6.1, and 9.8 Gbit/s
OBSAI: 3.1 Gbit/s.

Network

under test

Testing Unit

Testing Unit

FTB-700G/800 Series

CPRI/OBSAI 

Unframed, 

CPRI Framed L2

FTB-700G/800 Series

Network

under test

Testing Unit

Physical Loopback 

FTB-700G/800 Series

CPRI/OBSAI 

Unframed

Network

under test

Base Station (BTS)

FTB-700G/800 Series

CPRI Framed L2

RRH

1

 or 

FTB-700G/800 Series

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands