Home
/
EXFO
/
FTB-1
/
User Manual

EXFO FTB-1, User Manual

Share

Page: 333 / 675

EXFO FTB-1 User Manual Download Page 333

Test Results

NetBlazer

321

Alarms/Errors



LOF

(Loss of Frame)

RX

: OOF is present for at least 3 ms.

TX

: Generates error in all FAS bits continuously.



LOM

(Loss Of Multiframe)

RX

: OOM is present for at least 3 ms

TX

: Generates error in MFAS bits continuously.



OOF

(Out-Of-Frame)

RX

: FAS (bytes 3, 4, and 5) are in error for at least 5 consecutive OTU

frames.

TX

: Generates error in all FAS bits for 5 consecutive OTU frames.



OOM

(Out-Of-Multiframe)

RX

: MFAS are in error for at least 5 consecutive OTU frames.

TX

: Generates error in multiframe number for 5 consecutive OTU

frames.



TIM

(Trace Identifier Mismatch)

RX

: Expected SM SAPI and/or SM DAPI do not match the received SM

SAPI and/or DAPI for at least 3 consecutive TTI. This alarm is only
available when the Enable TIM SAPI OTU-TIM and/or DAPI OTU-TIM
check boxes are selected from page 285.

«
...
331
332
333
334
335
...
»

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands