manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 318

Test Results

306

FTB-700G/800 Series

Alarms/Errors

Ethernet 

Alarms

Link Down

 

RX

: The Ethernet connection is down meaning that there is a local or a 

remote fault condition. 

Local Fault Det.

1

 (Local Fault Detected) 

RX

: At least one of the following events is detected: Loss of bit 

synchronization, Loss of Block synchronization, WIS Link down, or 
High BER.

Local Fault Rcd.

1

 

(Local Fault Received)

RX

: The received data path contains the 

Local Fault

 signal.

Remote Fault

1

 

RX

: The received data path contains the 

Remote Fault

 status. 

1. Available with Ethernet 10Gbit/s interface.  

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands