manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 617

Glossary

NetBlazer

605

CPRI

Physical Interface

CPRI offers 8 options in terms of interface rates. Rates below 10G uses 
8B/10B line coding as per CPRI V6.0 while rates above 10G use 64B/66B 
coding. Depending on the rates used, scrambling is optional. Depending on 
the CPRI signal structure (Framed or Unframed) the scrambling is either 
manually configured or negotiated. 

Option

Rate

Line Coding

Protocol Version (Scrambling)

1

614.4 Mbit/s

a

a.

Not supported as presently not used in the field. 

8B/10B

Version 1: No scrambling 

2

1.2288 Gbit/s

3

2.4576 Gbit/s

4

3.0720 Gbit/s

5

4.9152 Gbit/s

Version 1: No scrambling
Version 2: Scrambling
(Scrambling is optional)

6

6.1444 Gbit/s

7

9.8304 Gbit/s

8

10.1376 Gbit/s

a

64B/66B

Version 2: Scrambling 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands