EXFO FTB-1 User Manual Download Page 128

Page: 128 / 675

Test Setup - Test Configurator, Timer, and System

116

FTB-700G/800 Series

1588 PTP

Pass/Fail Verdict

Pass/Fail Verdict

check box when selected (default) enables the use of the

pass/fail verdict. The global pass/fail verdict is based on the following
criteria: alarms (

Link Down

Loss Sync

Loss Announce

Unusable

and/or

QL Mismatch

(when

QL Mismatch Monitoring

is enabled)), or the

test is automatically aborted (service request denied, session canceled, or
no reply).

Restore 1588 PTP Defaults

Reverts the 1588 PTP test application to its default factory settings.

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands

EXFO FTB-1, User Manual

Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands