manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 265

Test Setup - Test Configurator, Timer, and System

NetBlazer

253

Signal - Signal Configuration (DSn/PDH)

Modify Loop Codes

 button

Allows the configuration of 10 DS1 loop code pairs. Configure each 
loop code name, Loop-Up and Loop-Down values. 

The name field allows up to 16 characters long. Loop-Up and 
Loop-Down range is from 3 to 16 bits (

000

 to 

1111111111111111

). 

The default DS1 loop codes correspond to the DS1 In-Band loop 
codes (Loop-Up=

10000

, and Loop-Down=

100

).

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands