manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 480

Test Functions

468

FTB-700G/800 Series

FEAC

Amount 

is the amount of codeword to be generated: 

1

 to

15

 

(default is 

10

). 

Inject 

generates error(s) according to the Codeword and mode 

selected. 

Loopback Commands 

Control 

Codeword

 is the loopack control codeword to be generated: 

Line 

Loopback Activate (00001110)

 - (Default) or 

Line Loopback 

Deactivate (00111000)

. 

Amount 

is the number of 

Control Codeword

 to be generated: 

1

 to 

15

 (default is 

10

). 

Channel 

Codeword

 is the channel codeword to be generated. 

Amount 

is the number of Channel Codeword to be generated: 

1

to

15 

(Default is 

10

). 

Inject

 generates the defined loopback command.

Channel Codeword

DS3 Line (00110110)

DS1 Line-No10 (01010100)

DS1 Line-No20 (01101000)

DS1 Line-No1 (01000010)

DS1 Line-No11 (01010110)

DS1 Line-No21 (01101010)

DS1 Line-No2 (01000100)

DS1 Line-No12 (01011000)

DS1 Line-No22 (01101100)

DS1 Line-No3 (01000110)

DS1 Line-No13 (01011010)

DS1 Line-No23 (01101110)

DS1 Line-No4 (01001000)

DS1 Line-No14 (01011100)

DS1 Line-No24 (01110000)

DS1 Line-No5 (01001010)

DS1 Line-No15 (01011110)

DS1 Line-No25 (01110010)

DS1 Line-No6 (01001100)

DS1 Line-No16 (01100000)

DS1 Line-No26 (01110100)

DS1 Line-No7 (01001110)

DS1 Line-No17 (01100010)

DS1 Line-No27 (01110110)

DS1 Line-No8 (01010000)

DS1 Line-No18 (01100100)

DS1 Line-No28 (01111000)

DS1 Line-No9 (01010010)

DS1 Line-No19 (01100110)

DS1 Line-All (00100110)

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands