EXFO FTB-1 User Manual Download Page 530

Page: 530 / 675

Test Functions

518

FTB-700G/800 Series

RTD



Disabled

: Indicates that the RTD feature is disabled. For example, this

condition occurs for DS0/E0 test case having all its timeslots set to
Idle/Tone.



: Indicates that the RTD measurement is not ready.

Reset

Resets the RTD results and measurement counts.

Delay

Indicates the time required for a bit to travel from the transmitter back to its
receiver after crossing a far-end loopback.



Last

indicates the result of the last Round Trip Delay measurement.



Minimum

indicates the minimum Round Trip Delay recorded.



Maximum

indicates the maximum Round Trip Delay recorded.



Average

indicates the average Round Trip Delay value.



Unit

measurement selections are

(default) and

Count

Indicates the total number of successful and failed measurements.



Successful

: A measurement is declared successful when the RTD is

smaller or equal to 2 seconds.



Failed

: A measurement is declared failed when the RTD is > 2

seconds.

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands

EXFO FTB-1, User Manual

Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands