EXFO FTB-1 User Manual Download Page 469

Page: 469 / 675

Test Functions

NetBlazer

457

APS

APS

From the

Test

menu, tap

Functions

, and the

APS

tab.

TX/RX



Switching Mode

, available for both TX and RX, selects the switching

mode:

Linear

(default) or

Ring



Request:

Bits 1 through 4 of the K1 byte.

Bits

1 to 4

Request

Linear mode

Ring mode

0000

No Request

Default value.

No Request (default)

0001

Do Not Revert

Reverse Request - Ring

0010

Reverse Request

Reverse Request - Span

0011

Unused

Exerciser - Ring

0100

Exerciser

Exerciser - Span

0101

Unused

Wait-to-Restore

0110

Wait-to-Restore

Manual Switch - Ring

0111

Unused

Manual Switch - Span

1000

Manual Switch

Signal Degrade - Ring

1001

Unused

Signal Degrade - Span

1010

Signal Degrade - Low Priority

Signal Degrade (Protection)

1011

Signal Degrade - High Priority

Signal Fail - Ring

1100

Signal Fail - Low Priority

Signal Fail - Span

1101

Signal Fail - High Priority

Force Switch - Ring

1110

Force Switch

Force Switch -Span

1111

Lockout of Protection

Lockout of Protection - Span/SF - P

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands

EXFO FTB-1, User Manual

Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands