manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 435

Test Results

NetBlazer

423

Summary (NI/CSU Emulation)

Summary (NI/CSU Emulation) 

From the

 Test

 menu, tap 

Results

, and the 

Summary

 tab. 

Status 

Status

 indicates the progress of the cable test as follows: 

Idle

 (test has not started)

In Progress

Completed

 

The Pass/Fail verdict is displayed next to the 

Test Status

 field, when 

enabled, based on the following criteria: The worst pair’s 

Wire Map

, 

Prop. Delay

, 

Delay Skew

, and 

Length

.

Start Time

Indicates the date and time the test has been started. The date and time is 
reset every time the test is restarted or reset. 

Auto-Response/Manual Loopback Status

Indicates the status of the loopback: 

Loopback Active

No Loopback

. 

Interface 

See 

Interface

 on page 311 for more information on Interface alarms/errors. 

DS1 

See 

DS1

 on page 300 for more information on DS1 alarms/errors. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands