EXFO FTB-1 User Manual Download Page 157

Page: 157 / 675

Test Setup - Test Configurator, Timer, and System

NetBlazer

145

Fibre Channel



Fabric Status

indicates the status of the Fabric switching network. The

status is not available when the discovered topology is Point-to-Point.



Logged-in

indicates that the login process has completed

successfully.



Failed

indicates that the login process is not completed

successfully or an error has been detected.



In Progress

indicates that the login process is running (not

completed yet).



Logged-out

(default) indicates that the system has not logged in

yet or has received a valid Logout command from the remote port.



Port Status

indicates the state of the port login process.



Logged-in

indicates that the login process has completed

successfully.



Failed

indicates that the login process is not completed

successfully or an error has been detected.



In Progress

indicates that the login process is running (not

completed yet).



Logged-out

(default) indicates that the system has not logged in

yet, has received a valid Logout command from the remote port, or
the Fabric status is either Failed, In Progress, or Logged-out.

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands

EXFO FTB-1, User Manual

Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands