manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 201

Test Setup - Test Configurator, Timer, and System

NetBlazer

189

Network

Prefix Mask

, available with 

Static

 mode, allows to specify a prefix 

that defines the subnet. The accepted range is 

0000:0000:0000:0000:0000:0000:0000:0000

 to 

FFFF:FFFF:FFFF:FFFF:0000:0000:0000:0000

. For example: 

Global Address: 2001:0DB8:0001:0002:02AA:00FF:FE11:1111
Prefix Mask: FFFF:FFFF:FFFF:0000:0000:0000:0000:0000 
Corresponding Prefix: 2001:0DB8:0001.

Default Gateway 

allows the configuration of the default gateway 

address to forward packets outside the subnet. 

Mode

Automatic

 (default) allows automatic selection of the default 

gateway. 

Static

 allows entering the default gateway IP address. 

Address

, available with 

Static

 mode, allows to enter the IP address 

of the Default Gateway. The accepted range is from 

0000:0000:0000:0000:0000:0000:0000:0000 

to 

FE80:0000:0000:0000:FFFF:FFFF:FFFF:FFFF

. The default address 

is 

FE80:0000:0000:0000:0000:0000:0000:0000

. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands