manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 108

Test Setup - Test Configurator, Timer, and System

96

FTB-700G/800 Series

Test Configurator Overview

Test Block displays an overview of the test settings and status. Tap 
on the test block to change the settings and to see detailed status. 

Clock Block displays an overview of the clock settings and status. 
Tap on the clock area to change the settings and to see detailed 
status. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands