EXFO FTB-1 User Manual Download Page 255

Page: 255 / 675

Test Setup - Test Configurator, Timer, and System

NetBlazer

243

Signal (Transport)



Line Coding



RX Termination



Power

indicates the received signal level in dBdsx for DSn or dBm for

PDH and SONET/SDH.



Amplitude

indicates the received signal amplitude as well as its MIN,

and MAX received values.

Signal

Line Coding

DS1

AMI

and

B8ZS

Default value.

DS3

B3ZS

AMI

and

HDB3

CMI

STS-1e/STM-0e

B3ZS

STS-3e/STM-1e

CMI

Signal

Termination

DS1/E1

Term

, Mon,

and

Bridge

Default value.

DS3/E3/E4/STS-1e/STM-0e/STS-3e/STM-1e

Term

, and

Mon

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands

EXFO FTB-1, User Manual

Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands