manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 278

Test Setup - Test Configurator, Timer, and System

266

FTB-700G/800 Series

Streams - Profile

Streams - Profile 

The Traffic Gen & Mon test application supports the configuration of up to 
16 different streams individually.

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, the protocol block, and 

the 

Profile

 tab. 

Note:

All parameters are configurable per stream. 

Stream Selection and Activation

Select the stream to be configured by either using the left/right arrow or by 
tapping over the stream numbers area then tapping on a specific stream 
number. An orange background indicates the selected stream while a 
green background indicates the streams that are enabled. 

Stream

 associates a name to the selected stream number. Default 

stream names are

 Stream 1 

to 

Stream n

. 

Enable

 check box when selected (cleared by default) enables the 

selected stream. However, the stream will be generated only when the 
test is started while the global 

Enable TX

 check box is selected from 

the 

Global

 tab. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands