manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 666

Index

654

FTB-700G/800 Series

Remote...................................................... 217
Remote block .............................................. 93
Remote Fault..................................... 306, 309
Remote IP Address .................................... 277
Remote Loopback ..................................... 359
Remote Modules Discovery ....................... 530
Remote Radio Head................................... 110
Remote to Local ........................................ 206
Remote unit in DTS Mode ......... 406, 424, 428
Remote unit in use and locked for DTS .... 405, 

424, 428

Renewal Interval........................................ 113
Replied Details........................................... 505
Report Content.......................................... 465
Request ..................................................... 457
Requesting MEP ID TLV ............................. 227
RES.................................... 482, 483, 484, 485
Reserved Bit............................................... 183
Reset ......................................................... 518
Reset button ............................................. 551
Resolve MAC ............................................. 223
Resolve MAC Address................ 175, 181, 205
Responder ................................................. 452
RESTART .................................................... 355
RESTART ACK............................................. 355
Restore 1588 PTP Defaults......................... 116
Restore Cable Test Defaults ....................... 124
Restore Carrier EThernet OAM Defaults..... 229
Restore CPRI/OBSAI Defaults...................... 130
Restore Default ................................. 236, 276
Restore Default at Start-Up ....................... 276
Restore EtherSAM Defaults ....................... 140
Restore ISDN PRI Defaults.......................... 168
Restore RFC 2544 Defaults ........................ 208
Restore RFC 6349 Defaults ........................ 219
Restore SyncE Defaults .............................. 275
Restore TCP Throughput Defaults.............. 278
Restore Test Application Defaults.............. 122
Results................................................. 33, 503
resume operation...................................... 564
Re-transmitted Frames .............................. 439
return merchandise authorization (RMA) .. 573

Revision ..................................................... 358
RFC 2544 ..................................................... 56

Global .................................................. 206

RFC 6349 ............................................. 57, 217
RFC 6349 Results ....................................... 411
RFC 6349 Test on Service 1........................ 192
RFI-V.......................................................... 339
R-LOF......................................................... 299
R-LOS......................................................... 299
RNR ........................................................... 353
Round Trip Delay ............................... 519, 520
Round Trip Latency.................................... 440
Round-Trip Latency.................................... 410
Round-Trip Latency Threshold ........... 132, 410
RR.............................................................. 353
RS .............................................................. 330
RS (J0)........................................................ 445
RS-FAS ....................................................... 331
RS-LOF ....................................................... 330
RS-OOF ...................................................... 330
RS-TIM ....................................... 285, 330, 445
RTD.................................................... 516, 519
RTT ............................................................ 412
Running..................................................... 517
Runt .......................................................... 307
RX button.................................................. 487
RX CCM ..................................................... 431
RX DMR ..................................................... 381
RX Frame Count ........................................ 387
RX Frames.................................................. 425
RX Frequency............................. 157, 245, 396
RX LBR ....................................................... 379
RX Line Utilization ..................................... 434
RX LMR...................................................... 382
RX LTR ....................................................... 522
RX OH Byte Details .................................... 486
RX Pattern ................................................. 118
RX Pattern Analysis.................................... 167
RX Pointer Adjustment .............................. 515
RX Power................................... 155, 241, 540
RX Rate...................................... 386, 390, 412
RX SLR ....................................................... 383

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands