EXFO FTB-1 User Manual Download Page 105

Page: 105 / 675

Test Setup - Test Configurator, Timer, and System

NetBlazer

Test Configurator Overview



Remote operation mode allows to select the remote operation
mode. Tap on the button to change the remote operation mode.



Remote

block displays and allows to change basic remote settings.

Tap on the

More

button to access all settings.



Transport Test Applications:



Ethernet Test Applications:

Physical

Interface Port

Test Application

Modify Structure

Test Block

Clock Block

Physical Clock Port

Interface Block

Arrows

Protocol Block

Topology

Physical

Interface Port

Test Application

Modify Structure

Protocol Block

Test Block

Clock Block

Physical Clock Port

Interface Block

Arrows

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands

EXFO FTB-1, User Manual

Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands