EXFO FTB-1 User Manual Download Page 295

Page: 295 / 675

Test Setup - Test Configurator, Timer, and System

NetBlazer

283

Traces (OTN)



SAPI OTU/ODU/TCM-TIM

check box, when selected (cleared by

default), allows editing the expected Source Access Point Identifier
(SAPI) and also enables OTU/ODU/TCM-TIM alarm monitoring.



DAPI OTU/ODU/TCM-TIM

check box, when selected (cleared by

default), allows editing the expected Destination Access Point Identifier
(SAPI) and also enables the OTU/ODU/TCM-TIM alarm monitoring.

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands

EXFO FTB-1, User Manual

Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands