manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 315

Test Results

NetBlazer

303

Alarms/Errors

Errors

FAS

 (Frame Alignment Signal) is only available with 

PCM30 CRC-4

 or 

PCM31 CRC-4

 framing. 

RX

: Bits 2 to 8 of the frame containing the FAS differ from 0011011.

CRC-4

 (Cyclical Redundancy Check) 

RX

: One or more bit errors are detected in a block of data through 

cyclical redundancy check. 

E-Bit 

(CRC-4 Error Signal) is only available with 

PCM30 CRC-4

 or 

PCM31 CRC-4

 framing. 

RX

: Bit 1 of sub-multiframe (SMF) II in frame 13 and/or 15 is set to 0 

indicating a sub-multiframe error. 

E2 

Alarms

Note:

Only AIS is available when the framing is set to Unframed.

AIS

 (Alarm Indication Signal) 

RX

: An unframed all-ones signal is received.

LOF

 (Loss Of Frame) 

RX

: Four consecutive incorrect frame alignment signals is received.

RAI 

(Remote Alarm Indication) 

RX

: Bit 11 of a framed E2 is set to “1”.

Errors

FAS

 (Frame Alignment Signal) 

RX

: Bits 1 to 10 of the first frame differ from 1111010000.

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands