manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 217

Test Setup - Test Configurator, Timer, and System

NetBlazer

205

Remote Details (iSAM)

For Manual Loopback Operation Mode 

MAC

, available with layer L2, allows to enter the destination MAC 

address of the remote. 

IP

, available with L3/L4, allows to enter the destination IP address of 

the remote. 

Resolved MAC address status,

 

available with L3/L4, indicates: 

Resolving

 when the ARP process is resolving. 

Resolved

 when the ARP process is resolved. 

Failed

 when the ARP process failed. 

Quick Ping

, available with layer L3/L4, tests if the destination IP 

address can be reached. A message displays if the ping attempt is 

Successful 

or 

Failed

. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands