manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 546

Test Control

534

FTB-700G/800 Series

Headset/DTMF Button

Headset

Note:

The settings here and on the platform are independent but platform 
settings may limit level control. For more information, refer to Adjusting 
Microphone and Speaker Volume from the platform user guide.

Speaker Volume

: The slide bar and +/- buttons are used to increase or 

decrease the volume of the speaker. 

MIC Volume

: The slide bar and +/- buttons are used to increase or 

decrease the volume of the microphone. 

DTMF 

The DTMF phone-style button grid is used to enter the standard DTMF tone 
(0-9,*,#). Alternatively the hard keyboard of the FTB-1 platform can be 
used. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands