EXFO FTB-1 User Manual Download Page 169

Page: 169 / 675

Test Setup - Test Configurator, Timer, and System

NetBlazer

157

Interface (Ethernet, Packet Sync, Fibre Channel, and Wireless)

RX Frequency



Frequency (GHz)

indicates the frequency of the input signal.



Offset (ppm)

indicates the frequency offset between the standard rate

specification and the rate at the input signal.

Note:

For both

Frequency

and

Offset

the following background colors are used.



Max Offset (ppm)

Negative

indicates the maximum negative frequency offset between

the standard rate specification and the rate from the received signal.

Positive

indicates the maximum positive frequency offset between the

standard rate specification and the rate from the received signal.

Background color

Description

Green

The frequency is in range.

Red

The frequency is out-of-range.

LOC

is also displayed.

Gray

Pending state.

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands

EXFO FTB-1, User Manual

Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands