EXFO FTB-1 User Manual Download Page 432

Page: 432 / 675

Test Results

420

FTB-700G/800 Series

Summary (ISDN PRI)



Frequency

column displays the following information:

RX (MHz)

indicates the monitored frequency of the input signal. The

following table lists the supported frequency monitoring range:

Offset (ppm)

indicates the offset between the standard rate

specification and the rate of the input signal.

Max (+) Offset (ppm)

indicates the offset between the standard rate

specification and the largest rate recorded from the received signal.

Max (-) Offset (ppm)

indicates the offset between the standard rate

specification and the smallest rate recorded from the received signal.

Note:

Values inside the standard range are presented on a green background
while the value outside are presented on a red background.

Interface

Standard Rate Specification

DS1

1544000 ±140 ppm

2048000 ±100 ppm

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands

EXFO FTB-1, User Manual

Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands