manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 186

Test Setup - Test Configurator, Timer, and System

174

FTB-700G/800 Series

MAC/IP/UDP

Transport Layer

1

 is disabled when the 

Network Layer

 is 

None

. 

MPLS

 - The 

MPLS Label

 check box, when selected (cleared by 

default), enables 1 or 2 MPLS labels allowing management and test 
frames to be transmitted and received. Only available with EtherSAM 
and Traffic Gen & Mon test applications. Not available with EtherSAM 
when the S-OAM check box selected or when 

Layer Mode

 is set to 

L2 Only

.

 

VLAN

 - The 

VLAN Tag

 check box when selected (cleared by default), 

enables up to 3 stacked VLAN. 

See 

VLAN

 on page 176 for additional VLAN settings. 

Preamble/SFD

Indicates that the frame structure contains the Preamble and SFD. 

1. Not available with EtherSAM when the 

S-OAM 

check box selected. 

Test Application

Transport Layer

EtherSAM

 

None

, 

UDP

 (default), 

TCP

RFC 2544

UDP

EtherBERT

UDP

 (default), 

TCP

Traffic Gen & Mon

None, UDP

 (default), 

TCP

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands