EXFO FTB-1 User Manual Download Page 259

Page: 259 / 675

Test Setup - Test Configurator, Timer, and System

NetBlazer

247

Signal - Signal Configuration (DSn/PDH)

Signal - Signal Configuration (DSn/PDH)

For SONET/SDH - DSn/PDH BERT, from the test menu, tap

Setup

Test Configurator

, and the protocol block. Only

Framing

setting and the

Loopback

button are available.

For DSn/PDH BERT and NI/CSU Emulation, from the test menu, tap

Setup

Test Configurator

, and the interface block.

Framing

Framing

allows the selection of the framing that will be used for

transmission.

DS1

DS3

E3/E4

Unframed
SF
ESF

SLC-96

Default value

Unframed
C-Bit Parity

M13

Unframed
PCM30

PCM30 CRC-4
PCM31
PCM31 CRC-4

Unframed
Framed

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands

EXFO FTB-1, User Manual

Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands